Pioneer AVIC-S1 Скачать руководство пользователя

Страница: 87 / 124

User's manual AVIC-S1

Traffic Messages

- 85 -

7.3

TMC categories

Overview

Traffic reports that are sent via TMC are always assigned certain
categories. Not all categories concern jams or obstacles that can

cause jams.
You can set from which categories you wish to have reports.

Setting TMC
categories

Open the T

RAFFIC

window. (refer to page 82)

In the T

RAFFIC

window, tap on the Traffic Settings button.

The T

RAFFIC

ETTINGS

window opens.

The TMC report categories are listed. You can scroll through the

list using the Up and Down buttons.
Each category shows the symbol that will be shown when there is

a report from this category.
A tick shows that the respective category will be shown.

No tick for a category means:

Reports for this category do not appear on lists of traffic
reports.

Reports for this category will not be shown on the map.

Reports for this category will not be taken into consideration

in the route calculation.

Show category / do
not show category

Tap on a category in order to add or remove the tick.

Perform this step for each category that you wish to change.

Close configuration

Tap on the Back button in order to close the T

RAFFIC

ETTINGS

window and return to the T

RAFFIC

window.

Содержание AVIC-S1





























































































































Результаты поиска

Содержание AVIC-S1

Отзывы:

Похожие инструкции для AVIC-S1

Бренды по названию

Популярные бренды

Pioneer AVIC-S1, Руководство пользователя

Результаты поиска

Содержание AVIC-S1

Отзывы:

Похожие инструкции для AVIC-S1

Бренды по названию

Популярные бренды