Pioneer AVIC-S1 Скачать руководство пользователя

Страница: 15 / 124

User's manual AVIC-S1

Using the Navigation System for the First Time

- 13 -

2.2

Switching on the navigation system

As soon as you have connected the navigation system to the

power supply you can start to use it for the first time.

Slide the main switch on the back of the device to ON.
If the main switch is already switched to ON, then press the

On/Off button on the top of the device.

The PIONEER start screen appears briefly during start-up.
At the first start the following message appears:

Read the message, and touch OK if you agree with the
written warning.

2.3

Basic settings

Basic Settings

When you start AVIC-S1 for the first time, you will be asked

to specify the language in which you would like to operate the

navigation system,

for the time zone valid for your location, this was you can
correctly state arrival times, and

to specify the desired format for the time (12hr/24hr) and
distances (km/mi).

Содержание AVIC-S1





























































































































Результаты поиска

Содержание AVIC-S1

Отзывы:

Похожие инструкции для AVIC-S1

Бренды по названию

Популярные бренды

Pioneer AVIC-S1, Руководство пользователя

Результаты поиска

Содержание AVIC-S1

Отзывы:

Похожие инструкции для AVIC-S1

Бренды по названию

Популярные бренды