Pioneer AVIC-S1 Скачать руководство пользователя

Страница: 112 / 124

User's manual AVIC-S1

- 110 -

Regional Settings

8.14.2

Time Zone

Time Zone

With this setting you can establish valid time zones for your
location. This setting is important for the correct calculation of

probable arrival times.
Tap on the button to open the T

IME

ONE

window.

Time Zone

The current setting is shown on the button.
1.

Tap on the button to open the T

IME

ONE

window.

Tap on the time zone that applies to your location. Use Up
and Down to scroll through the list. The display of the major

cities of the respective time zone should help you to choose
the correct one.
The T

IME

ONE

window is shown again.

Daylight Saving Time The current setting is shown on the button.

Tap on the Daylight saving time button to change the
setting:

Setting

Meaning

Daylight saving time is switched on

Off

Daylight saving time is switched off

8.14.3

Time Format

Time Format

With this setting you establish which units of measurement
should be used for times.
The current setting is shown on the button. Tap on the button to
change the setting.

Setting

Meaning

24h

Displays the time in AngloSaxon 12-hour
format.

12h

Displays the time in European 24-hour
format.

Содержание AVIC-S1





























































































































Результаты поиска

Содержание AVIC-S1

Отзывы:

Похожие инструкции для AVIC-S1

Бренды по названию

Популярные бренды

Pioneer AVIC-S1, Руководство пользователя

Результаты поиска

Содержание AVIC-S1

Отзывы:

Похожие инструкции для AVIC-S1

Бренды по названию

Популярные бренды