Pioneer AVIC-S1 Скачать руководство пользователя

Страница: 68 / 124

User's manual AVIC-S1

- 66 -

Zoom

5.2

Zoom

Zoom level, Scale

The map can be shown in variousl zoom levels in all views. After
starting navigation the autozoom mode is active: the zoom level

changes automatically depending on the current speed.
The zoom level bar is displayed as soon as you tap on one of the

buttons Zoom out or Zoom in.

The scale is shown to the left alongside the Zoom in button on

the lower edge of the display.

A short distance piece shows the reference distance on the
display. The number above this indicates which distance this
reference refers to in reality.

Zoom out
Tap on the Zoom out button in order to increase the map scale.

The map section shown will become larger but there will be less
precision of detail.

Zoom in
Tap on the Zoom in button in order to reduce the map scale. The

map section shown will become smaller but the precision of detail
will increase.

Zoom level bar
The red zoom controller shows the current level of zoom.
To the left of the zoom level bar there are some buttons using

which you can set a specific map scale.

Note: In all views, zooming is only possible when the map is
being displayed in 2D mode.

Содержание AVIC-S1





























































































































Результаты поиска

Содержание AVIC-S1

Отзывы:

Похожие инструкции для AVIC-S1

Бренды по названию

Популярные бренды

Pioneer AVIC-S1, Руководство пользователя

Результаты поиска

Содержание AVIC-S1

Отзывы:

Похожие инструкции для AVIC-S1

Бренды по названию

Популярные бренды