167
PDP-5020FD
5
6
7
8
5
6
7
8
A
B
C
D
E
F
Preparation before adjustment
[Replacement with the panel for service is completed.]
[To the Main flowchart (1)]
Turn the unit on. / [PO
N
]
Enter Factory mode. / [FAY]
Set PM/B1-B5 to CLEAR (to clear the pulse meter). / [CPM]
Set HR-MTR to CLEAR (to clear the hour meter). / [CHM]
Turn the unit off. / [POF]
Turn the unit on. / [PO
N
]
Enter Factory mode. / [FAY]
Display CMB MASK 01 (moving ramp). / [MKC S01]
Select
V
ideo 60-Hz sequence. / [
V
FQ S03]
∗
To reflect the results of log clearing for each correction function,
the unit must be turned off then back on again. Before adjust-
ment, be sure to turn the unit off then back on again.
Note:
*
W
hen you perform the adjustment with RS232C commands, issue the following commands in addition.
* If the unit is shut down in the middle of performing the adjustment flowchart, reissuing of the command is required.
[PAV S00]
: To set panel drive mode to Factory
[VFQ S03]
: To set Drive Sequence to
V
ideo 60-Hz
[WBI S01]
: To temporarily reset the Panel
W
B adjustment value to default (
W
BI S00 cancels this setting.)
[PGR S00]
: To set the gamma R value to that for Factory mode
[PGG S00]
: To set the gamma G value to that for Factory mode
[PGB S00]
: To set the gamma B value to that for Factory mode
[DIZ S03]
: Dither O
N
, L dither O
N
, noise OFF.
[$1
8
00000001]
: LUT mode O
N
Procedures for resetting
corrections for change
over time
Perform aging for 30 minutes.
Enter the tentative setting value of the replacement panel
Procedures for stabilizing the
panel before adjustment
Note:
The symbol "
α
" denotes the adjustment value plus 0.
Note:
"+0" shows
α
.
AWU1340 Data
VOF=129
VRP=031 V1F=143 V3F=12
8
+
α
Indication example of the adjustment label
of service panel
Data 0
8
/02/2
8
Chassis CXX99999
Time 1
8
:27 Pnl FD4A0
8
0
8
100123
V4F=172 Hour Meter
_ _ _ _ _ _ _ _ _ _
H
Setting Item
Tentative Setting Value
V
OL SUS / [
V
SU
∗∗∗
] 12
8
V
OL OFFSET / [
V
OF
∗∗∗
]
V
OF indication value
V
OL RST P / [
V
RP
∗∗∗
]
V
RP indication value
V
OL XPOFS1 / [
V
X1
∗∗∗
] 0
8
5
V
OL XPOFS2 / [
V
X2
∗∗∗
] 047
V
OL Y
N
OFS1 D / [
V
1F
∗∗∗
]
V
1F indication value
V
OL Y
N
OFS3 D / [
V
3F
∗∗∗
]
V
3F indication value +0
V
OL Y
N
OFS4 D / [
V
4F
∗∗∗
]
V
4F indication value
V
OL Y
N
OFSA D / [
V
YF
∗∗∗
] 12
8
∗
To store the
V
FQ S03 command in memory, transmit it after
displaying the mask.
∗
Each setting value described on the adjustment label
denotes an indicated data value but not a real voltage value.
Therefore, just enter the data value as a setting value.
Содержание ARP3476
