Pinnacle microguard Скачать руководство пользователя страница 43

Страница: 43 / 48

Appendix “D”

USB Diagnostic Codes

Model MG or DR USB Diagnostic Codes: Master Controls USB port

You must install the Silabs CP210x USB driver on your windows PC. Check your

Device Manager for Silabs COM port#. You read the port at 115200 Baud 8N1

D-1

Microguard MG or DR USB Diagnostics Codes:
Master controls USB port

Char

Description

B or b

First or Second Pylon set Blocked

repeats when # of blocked beams changes

M or m

First or Second Pylon set Blocked during MUTE-OUT condition

Guard stays GREEN

C or c

First or Second Pylon set Cleared after a Block

E or e

First or Second Pylon set no Blocked beams during MUTE-OUT condition

Light Curtain in MUTE-OUT (Guard was GREEN before going into MUTE-OUT)

Light Curtain no longer in MUTE-OUT

Check EEPROM

Start & Stop ReWriting EEPROM

Should only happen 1

time programmed

Fault found active in EEPROM at Startup

Previously powered down with an

uncleared Fault

AutoBlank load

Should always see this

“Soft Ver= R34r.1012.MG”

Scroll this string on LED display

Only RST F1 push can interrupt this

Version Display scroll finished

“RST”

String on LED display

Then jmp to FAULT routine

Enter Fault() routine

x: 0=Slave in Fault() routine, 1=Slave not in Fault() routine

Should be F0

Writing to EEPROM new Fault code

V<cr>

Clearing Active Fault

Someone Hit RESET button while in a Fault

x y

x & y: upper and lower bytes of Fault Code just cleared.

Displayed in HEX

Return from Fault() routine

Not first time returning

P<cr>

Return from Fault() routine

First time returning

9 lines of 2 byte HEX showing the last 9 Fault Codes

First to Last

Hold RESET button down at power-up

LED displays 9 fault codes

End of Fault

First Time return from FAULT()

Run Initial pylon TEST

One time after power-up only

xxxx m

Pylon length , performing SHORT LED test

1 SCAN of pylon

“Wait”

Done with initial SHORT LED SCAN

If numbers appear without an F, then problems communicating with Slave

Bad Auto Blank memory

See page D-2 for instructions.

Содержание microguard

















































Результаты поиска

Содержание microguard

Отзывы:

Похожие инструкции для microguard

Бренды по названию

Популярные бренды

Pinnacle microguard, Руководство по установке

Результаты поиска

Содержание microguard

Отзывы:

Похожие инструкции для microguard

Бренды по названию

Популярные бренды