Pinnacle microguard Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 48

background image

Figure 14: Swing-Arm Mounting Bracket Dimensions

Pedestal

The heavy duty, all-welded steel pedestal floor mounts

can be used for mounting either the MicroGuard Metal

Box or DIN-rail Controller Module light curtain or

cornering mirrors. Sliding mounts on the pedestal are

universal in design and are supplied standard. Unique

floating base on pedestal is designed to compensate

for uneven floors. Pedestal is fabricated from 12 gauge

steel, the base is ¼” steel plate, and the entire unit is

painted OSHA yellow.

Standard height = 72” (model 8000)

Optional height = 96” (model 8096)

Do not mount pedestal to floor until

you have fully installed your guarding system and know

it is operating properly in its current position on the floor.

Pedestals must be bolted to the

floor after installation;

they must not be movable.

11-183

Standard Single mounting bracket

(shown)

11-184

Special Dual pedestal mounting

bracket. Has two mounting studs 90

deg apart. Allows both Emitter and

Receiver pylon on one pedestal.

Requires SMB option on pylons.

Figure 13: Pedestal Dimensions

Accessories

Metal Box Controller Module

22

Stud is 3/8”-16 x 10/16” long

Model 9000 and 9500

Excellent method of mounting the light guard for press brakes or when the light guard is to be moved for die setups

or machine maintenance. Model 9000 consists of three 180-pivot points along with light guard diagonal movement

capability for virtually unlimited light guard positioning. Two-inch square tubing 3/16” thick painted OSHA yellow

which mounts directly onto the machine housing and makes for a heavy duty yet versatile mounting bracket. Model

9500 consists of two 180-pivot points and one adjustable length arm.

Model 9000 Swing Arm Brackets

Model 9500 Swing Arm Brackets

«
...
30
31
32
33
34
...
»

Содержание microguard

















































Отзывы:

Нет отзывов

Похожие инструкции для microguard

Бренд: ABB Страницы: 2

Бренд: ZIMO Страницы: 38

Бренд: dbx Страницы: 52

Бренд: Hankscraft Runxin Страницы: 58

ROBO Cylinder RCP2 Series

Бренд: IAI Страницы: 5

Бренд: PACH & COMPANY Страницы: 4

Бренд: Taoglas Страницы: 2

Бренд: Vega Страницы: 20

Бренд: Balboa Страницы: 23

Бренд: Balboa Страницы: 2

Бренд: brel-motors Страницы: 2

CIATControl OPC Server

Бренд: CIAT Страницы: 32

Бренд: Danfoss Страницы: 8

Infi 90 IMAOM01

Бренд: Bailey Страницы: 44

Бренд: Fluidmaster Страницы: 2

Бренд: KEY Страницы: 16

Бренд: M-system Страницы: 7

Temp Alert TA2HL

Бренд: Winland Electronics Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды