Pilz PSEN op2H-A Series Скачать руководство пользователя страница 33

Страница: 33 / 61

OPERATING MANUAL

PSEN op2H-A series

6.1 Reset to factory configuration

The user has the option to re-establish the light curtain’s factory configuration by operating
the pushbuttons as described below:

1. Press the CONFIRM button and keep it held down for at least 9 s (but not more than

30 s, so that the light curtain is not blocked)

2. The LEDs flash briefly, indicating that the light curtain has been reset to the factory

configuration

3. After the reset has occurred, the light curtain resumes its normal operation with the

factory configuration.

NOTE: Restoring the factory settings will delete the BCM configuration.

6.2 Function list

NOTE: The table highlights the default configuration in bold.

Legend for LED display in RX/TX function list

LED off, LED is not relevant for the information in the “Function” column

LED off, LED is relevant for the information in the “Function” column

LED yellow, value in the “Setting” column is valid for the information in the
“Function” column

LED red, value in the “Setting” column is valid for the information in the “Function”
column

LED green, value in the “Setting” column is valid for the information in the
“Function” column

List of RX functions in muting mode

(LED 3 lights up yellow)

Function

LED

No.

Setting

LED status

LEVEL

Partial Muting

2
3

See the following table

EDM

Activated

Deactivated

Restart mode

Auto

Manual

Muting direction

T (bidirectional)

L (one-directional)

Muting timeout

10 min

Infinite

Activation of
override

Level

Edge

1003069-EN-03

Содержание PSEN op2H-A Series






























































Результаты поиска

Содержание PSEN op2H-A Series

Отзывы:

Похожие инструкции для PSEN op2H-A Series

Бренды по названию

Популярные бренды

Pilz PSEN op2H-A Series, Руководство по эксплуатации

Результаты поиска

Содержание PSEN op2H-A Series

Отзывы:

Похожие инструкции для PSEN op2H-A Series

Бренды по названию

Популярные бренды