Pilz PIT m4SEU Скачать руководство пользователя страница 59

Страница: 59 / 68

Operation

Operating Manual PIT m4SEU
1004648-EN-02

| 59

8.6

Troubleshooting

If an error occurs on the PIT m4SEU, the last operating mode to be set will be retained.

Error

Possible cause

Remedy

Unable to switch the op-
erating mode

Multiple pushbuttons oper-
ated

Make sure that only one push-
button is operated

Operating time too long or
too short

Make sure that the period of op-
eration is observed

Transponder key is not de-
tected

Make sure that the transponder
key on the PITreader is inserted
correctly

No valid permission

Make sure that you use a
transponder key that has the re-
quired permission.
Ensure that the PITreader inter-
face is connected correctly.
See also the PITreader operat-
ing manual.

Device error

- The DIP switch setting was
changed during operation

- Invalid configuration via the
DIP switch setting

Delete error

Please refer to the timing diagram for

Device error [

27]

8.6.1

Delete error

Procedure:

}

Switch off device (power off)

}

Configure DIP switch setting as shown (all switches to ON)

4 3 2 1

Off

}

Device restart → device error is still displayed

}

Switch off device

}

Configure required DIP switch position

}

Device restart → Error deleted

8.7

Diagnostics

Status information is sent to the interface for status information (SIo0 … SIo3) and to the
PITreader.

8.7.1

Status information about the interface for status information

Various status information can be signalled via the interface for status information (see

Block diagram [

16]

). The status information can be evaluated through a control system

(see

Interface for status information [

23]

Содержание PIT m4SEU





































































Результаты поиска

Содержание PIT m4SEU

Отзывы:

Похожие инструкции для PIT m4SEU

Бренды по названию

Популярные бренды

Pilz PIT m4SEU, Руководство по эксплуатации

Результаты поиска

Содержание PIT m4SEU

Отзывы:

Похожие инструкции для PIT m4SEU

Бренды по названию

Популярные бренды