19
CV-Table
CV
Description
Area
Value*
1
Locomotive address
DCC: 1 - 127
Motorola: 1 - 80
3
3
2
Minimum speed
(the speed from 0 until the locomotive is running at speed step 1)
1 - 63
1
1
3
Acceleration delay
1 means every 5 milliseconds the actual motor speed is increased by 1. If the maximum motor speed is 200 (CV 5 = 50 or CV 94 = 200),
then the acceleration rate from 0 to maximum speed is 1 second
0-255
25
25
4
Braking rate
(time factor like CV 3)
0-255
6
6
5
Maximum speed
(must be greater than CV 2)
1 - 63
45
45
6
Average speed
(must be greater than CV 2 and less than CV 5)
1 - 63
13
13
7
Software version
(The processor can be updated)
-
differently
162
8
Manufacturer identification
decoder reset, values like CV 59
different
162
117
17
18
Long locomotive address
17 = higher value Byte
18 = lower value Byte
1 - 9999
192 - 231
0 - 255
2000
199
208
2000
199
208
29
DCC standard configuration
Bit 0=0 Normal direction of travel
Bit 0=1 Opposite direction of travel
Bit 1=0 14 Speed steps
Bit 1=1 28 Speed steps
Bit 2=0 DCC-only mode
Bit 2=1 Automatic analog/digital recognition
Bit 3=0 RailCom
®
turned off
Bit 3=1 RailCom
®
turned on
Bit 4=0 Speed steps over CV 2, 5, and 6
Bit 4=1 Use the characteristic curve from CV 67 - 94
Bit 5=0 Short address (CV1)
Bit 5=1 Long address (CV 17/18)
0-63
14
0
30
Error codes for function outputs, motor, and temperature monitoring:
1 = fault function outputs, 2 = fault motor, 4 = overheating
0-7
0
14
33-46
Easy function mapping
Assignment of function outputs to CVs
CV 33 Lighting function key (F0) when moving forward
CV 34 Light function key (F0) when in reverse
CV 35 Function key F1
CV 36 Function key F2
CV 37 Function key F3
CV 38 Function key F4
CV 39 Function key F5
CV 40 Function key F6
CV 41 Function key F7
CV 42 Function key F8
CV 43 Function key F9
CV 44 Function key F10
CV 45 Function key F11
CV 46 Function key F12
Assignment of individual bits (with CV100 / 101 bit x = 0, standard)
Bit 0 Front light output
Bit 1 Rear light output
Bit 2 Function output A1
Bit 3 Function output A2
Bit 4 Function output A3
Bit 5 Function output A4
Bit 6 Switching (Shunting)
Bit 7 Acceleration / deceleration
0-255
1
2
4
8
16
32
64
128
1
2
4
8
16
32
64
128
0
0
0
0
0
0
0
59
Resetting to factory settings
(also possible via CV8)
1 = CV 0 - 256, as well as CV257 - 512 (RailCom
®
Bank 7)
2 = CV 257 - 512 (RailCom Plus
®
Banks 5 & 6)
3 = CV 257 - 512 (extended function mapping banks 1 & 2)
4 = CV 257 - 512 (modulation function outputs banks 3 & 4)
0 - 4
0
132
