background image

 

 

 

 

CONTENTS 

 

1

 

INTRODUCTION

 ......................................................................................................................................... 4

 

1.1

 

Unpacking the HS1

 ............................................................................................................................. 4

 

1.2

 

Handling the HS1.

 ............................................................................................................................... 4

 

1.3

 

HS1.

 ...................................................................................................................................................... 5

 

2

 

INSTALLATION

 ........................................................................................................................................... 5

 

2.1

 

Installing a single axis HS1 unit.

 ....................................................................................................... 5

 

2.2

 

Installing a two axis HS1 unit

 ............................................................................................................ 6

 

2.3

 

Installing a three axis HS1 unit

 ......................................................................................................... 6

 

3

 

GROUND LOOPS

 ....................................................................................................................................... 7

 

3.1

 

Prevention and identification of ground loops

 ................................................................................. 7

 

4

 

OPERATING THE NANOPOSITIONING STAGE

 .................................................................................. 7

 

4.1

 

Operating in closed loop mode

 ......................................................................................................... 7

 

4.2

 

Care during operation

 ......................................................................................................................... 8

 

 

 

Содержание HS1









Отзывы: