PIE PIECAL 434 Скачать руководство пользователя страница 12

Practical Instrument Electronics

82 East Main Street Suite 3.14 • Webster, NY 14580 Tel: 585.872.9350 • Fax: 585.872.2638 • [email protected] • www.piecal.com

Page 12

Source/Power & Measure Two Wire Transmitters

Ranges and Resolution

0.000 to 24.000 mA or -25.00 to 125.00% of 4-20 mA

Accuracy

≤ ± (0.01 % of R0.002 mA)

Noise

≤ ± ½ Least Significant Digit

Temperature effect

≤ ± 0.005 %/°C of FS

Loop compliance voltage

≥ 24 DCV @ 20.00mA

Loop drive capability - Leak Detection Off

Loop drive capability - Leak Detection On

1200 Ω at 20 mA for 15 hours nominal; 
950 Ω with Hart Resistor enabled
1000 Ω at 20 mA for 15 hours nominal; 
750 Ω with Hart Resistor enabled

Battery life

≥ 30 hrs at 12 mA nominal; ≥ 25 hrs with backlight on

2-Wire Transmitter Simulation

Accuracy

Same as Source/Power & Measure

Voltage burden

≤ 2V at 20 mA

Overload/Current limit protection

24 mA nominal

Loop voltage limits

2 to 60 VDC (fuse-less protected from reverse polarity 

connections)

Battery life

≥ 125 hours nominal; ≥ 100 hrs with backlight on

Voltage Read

Range and Resolution

-60.00 to +60.00 VDC Full Span (FS)

Accuracy

≤ ± 0.05 % of FS

Temperature effect

≤ ± 100 ppm/°C of FS

Input resistance

≥ 2 MΩ

Battery life

≥ 125 hours nominal; ≥ 100 hrs with backlight on

PIECAL 434 Specifications (continued)

(Unless otherwise indicated all specifications are rated from a nominal 23 °C,

70 % RH for 1 year from calibration)

Accessories

INCLUDED:
 

Carrying Case with Belt Loop   

 

 

Part No. 020-0205

OPTIONAL:
 

AC ADAPTOR (200 to 240 VAC)  

 

 

Part No. 020-0100

 

AC ADAPTOR (100 to 120 VAC)   

 

 

Part No. 020-0101

 

Ni-MH 1 Hour Charger w/4 Ni-MH AA Batteries 

 

Part No. 020-0103

 

 

(100-120 V AC input for North America Only)

www.

.com

[email protected]

1.800.561.8187

Содержание PIECAL 434













Отзывы: