PI M-230 Series Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 47

PI M-230 Series Скачать руководство пользователя страница 31

7 Maintenance

M-230 Linear Actuators

MP102E

Version: 1.2

27

7.1 General Notes on Maintenance

NOTICE

Damage due to improper maintenance!

The M-230 can become misaligned as a result of improper maintenance.



Do not loosen any sealed screws.

7.2 Lubricating the M-230

Depending on the operational conditions and the period of use of the linear actuator,
the following maintenance measures are required.

Spreading lubricant



If you operate the M-230 continuously on a small travel range (<20% of the

entire travel range), perform a maintenance run every 2000 motion cycles
across the entire travel range.

Lubrication

Under laboratory conditions, the linear actuator needs extra lubrication in exceptional
cases only. For continuous industrial use the lubrication intervals must be defined
individually.



Do not lubricate the M-230 without consulting our customer service

department (p. 31).



To lubricate, follow the instructions given in the maintenance manual which

you can obtain from our customer service department.

7.3 Cleaning the M-230

Prerequisites



You have disconnected the linear actuator from the controller.

7

Maintenance

«
...
29
30
31
32
33
...
»

Содержание M-230 Series
















































Отзывы:

Нет отзывов