phytron phyMOTION POWM01.1 Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 31

phytron phyMOTION POWM01.1 Скачать руководство пользователя страница 21

phytron

21

MA 1273-A004 EN

USB interface

Factory settings:

115 200 baud

8 data bits

1 stop bit

no parity

Protocol:

<STX>

|

address | data | separator | check sum

| <ETX> | <CR> | <LF>

Baud rate

and

interface parameter

can be adjusted after installation with the

phy

LOGIC

TM

ToolBox in the menu item

Options/interface parameter.

A direct connection from the PC to the POWM01 is made with the USB cable type A-B.

There the USB port of the PC (type A) is directly connected with the USB port of the

controller (type B).

Fig. 6: X5 Com: USB port type B (DIN IEC

61076-3-108)

Fig. 7: Wiring scheme PC



POWM01

by cable A-B

i

USB driver

To use the USB interface please install the appropriate USB driver in

advance before connecting the phy

MOTION

TM

.

-  Install the USB drivers from the delivered phytron CD.
-  Administrator authorizations are required for the driver installation.
-  Use a USB cable with a maximum length of 2 m!
-  If you want to test several USB devices, which are identical in

construction, you should use the same USB port on the PC. Thus, you

avoid changing the COM port number.

«
...
19
20
21
22
23
...
»

Содержание phyMOTION POWM01.1
































Отзывы:

Нет отзывов