background image

Manual POWM01 / POWM02 

 

MA 1273-A004 EN

 

2

 

 

 
 
 
 
 
 
 
 
 
 

 2013 

All rights with: 
Phytron GmbH 
Industriestraße 12 
82194 Gröbenzell, Deutschland 
Tel.: +49(0)8142/503-0 
Fax: +49(0)8142/503-190 
Intention of the manual: 
In this manual you will find descriptions and specifications of the 

phy

MOTION

TM

 module: 

Power Supply POWM01 and POWM02 
This manual is a supplementary volume to the operating instructions 

phy

MOTION

TM 

Modular Multi-axis Controller for Stepper Motors 

In the manual 

phy

MOTION

TM

 Modular Multi-axis Controller for Stepper Motors 

(http://www.phytron.de/

phy

MOTION) are the descriptions of the features and specifications 

for the 

phy

MOTION

TM

 stepper motor controller. 

 
Every possible care has been taken to ensure the accuracy of this technical manual. All 

information contained in this manual is correct to the best of our knowledge and belief but  

cannot be guaranteed. Furthermore we reserve the right to make improvements and 

enhancements to the manual and / or the devices described herein without prior 

notification. 
We appreciate suggestions and criticisms for further improvement. 
Email address: [email protected] 
Questions about the use of the product described in the manual that you cannot find 

answered here, please contact your representative of phytron (http://www.phytron.eu/) in 

your local agencies. 

Содержание phyMOTION POWM01.1
































Отзывы: