Phytec phycore i.mx7 Скачать руководство пользователя страница 38 | Manualshive

Страница: 38 / 43

background image

PCM-061/phyCORE-i.MX7 System on Module

L-821e_2

© PHYTEC America L.L.C. 2017

38

9.3

I

2

C

The phyCORE-i.MX7 provides four independent I

2

C buses at the phyCORE connector directly from the processor. I2C1,

I2C2, I2C3, and I2C4. The I2C1 bus is pulled up to the NVCC_3V3 rail via 2.2KOhm resistors and connects to the PMIC (U2),
EEPROM (U11), and RTC (U10). I2C2-4 require external pull-up resistors on custom Carrier Board designs. The following
table shows the reserved addresses for the internal components of the phyCORE-i.MX7.

Table 11. I2C1 Reserved Addresses

Device

Address

RTC

0x68

EEPROM

0x50

PMIC

0x08
0x09
0x0A
0x0B
0x0C
0x0D
0x0E
0x0F

9.4

PCI Express

The phyCORE-i.MX7 provides a single lane PCI Express Gen 2.0 interface with an integrated PHY supporting a data rate up
to  5Gbps.  The  PCIe  reference  clock  into  the  processor  is  provided  by  an  external  100MHz  oscillator  circuit  with  HCSL
termination.  Coupling  capacitors  are  not  provided  on  the  SOM  for  the  differential  TX  data  signals.  These  TX  coupling
capacitors should be implemented on a carrier board.

A 1.5V supply rail (VLDO2_1V5) is provided at the phyCORE-Connector from the PMIC to support Mini-PCI Express on a
carrier board). This 1.5V rail can provide a load current of up to 250mA.

NOTE:

According to the PCI Express Mini Card Electromechanical Specification the maximum peak current for the 1.5V rail is
500mA. Not all devices will need this maximum load current, or even utilize the 1.5V rail. However, if the 250mA
supplied by the PMIC rail is not sufficient, a regulator should be implemented on a carrier board to provide 1.5V from
the main system power.

Refer to the i.MX7 Technical Reference Manual for further details regarding PCI Express.

«
...
36
37
38
39
40
...
»

Содержание phycore i.mx7












































Отзывы:

Нет отзывов

Похожие инструкции для phycore i.mx7

DCDC SBC Series

Бренд: Infineon Страницы: 17

Бренд: MSI Страницы: 76

GA-MA785GMT-UD2H

Бренд: Gigabyte Страницы: 104

Бренд: DFI Страницы: 5

Бренд: Gigabyte Страницы: 100

Бренд: Gigabyte Страницы: 40

Бренд: Avalue Technology Страницы: 79

Бренд: ON Semiconductor Страницы: 7

Бренд: California Eastern Laboratories Страницы: 34

Бренд: Biostar Страницы: 67

Бренд: Texas Instruments Страницы: 20

Бренд: Fastrax Страницы: 12

NCP45491PMNGEVB

Бренд: ON Semiconductor Страницы: 9

D850MV - Desktop Board Motherboard

Бренд: Intel Страницы: 25

Бренд: Zeal-All Страницы: 9

Бренд: e2v Страницы: 39

Бренд: EPOX Страницы: 55

Бренд: Lantronix Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды