Phoenix Contact AXC F 1152 Скачать руководство пользователя страница 10

Страница: 10 / 113

AXC F X152

10 / 112

PHOENIX CONTACT

107708_en_08

1.7

UL warning notes

Valid for AXC F 1152 and AXC F 2152

If the device is not used in the specified manner, the protection provided by the device may

be impaired.

SELV - Limited energy according UL/IEC/EN 61010-1 or NEC Class 2

1.8

Notes on using the AXC F 2152 controller in poten-

tially explosive areas

Approval in accordance with ATEX directive 2014/34/EU and IECEx scheme

The category 3 device is designed for installation in zone 2 potentially explosive areas.

The device satisfies the requirements of EN/IEC 60079-0 and EN/IEC 60079-7.

Installation, operation, and maintenance must only be carried out by qualified electricians.

The IP20 degree of protection (IEC 60529/EN 60529) of the device is intended for use in a

clean and dry environment. Do not subject the device to mechanical and/or thermal loads

that exceed the specified limits.

The device must be stopped and immediately removed from the Ex area if it is damaged,

was subjected to an impermissible load, stored incorrectly or if it malfunctions.

The device is not designed for use in atmospheres with a danger of dust explosions.

This device must be installed in an area that is no longer classified as pollution degree 2 in

accordance with IEC 60664-1.

If this device is used in a zone 2 environment, it must be installed in a housing that at least

meets the requirements of IP54 degree of protection in accordance with IEC 60079-7 or an-

other degree of protection in accordance with IEC 60079-0, section 1.

•

Follow the installation instructions as described.

Please note:

From 2020 on, the AXC F 2152 is available with approval for potentially explosive areas.

In this case, the approval is printed on the device.

•

Before using the device in a potentially explosive area, make sure that your device

has the required approval.

The indicators and certificate numbers of the available approvals are printed on the de-

vice:

–



II 3 G Ex ec IIC T4 Gc

–

TÜV 19 ATEX 8356 X

–

IECEx TUR 19.0031X

WARNING: Explosion hazard

•

Please make sure that the following notes and instructions are observed.

Содержание AXC F 1152


















































































































Результаты поиска

Содержание AXC F 1152

Отзывы:

Бренды по названию

Популярные бренды

Phoenix Contact AXC F 1152, Установка, запуск и эксплуатация

Результаты поиска

Содержание AXC F 1152

Отзывы:

Бренды по названию

Популярные бренды