5
4
TVTVTVTV
VC
R
VCRVCRVCR
CB
L
CB
L
CB
L
CB
L
SA
T
SA
T
SA
T
SA
T
D
VD
DV
D
DV
D
DV
D
AUDI
O
AUDI
O
AUDI
O
AUDI
O
PO
W
ER
PL
AY
PL
AY
PL
AY
PL
AY
ST
O
P
ST
O
P
ST
O
P
ST
O
P
RE
C
RE
C
RE
C
RE
C
PA
US
E
PA
US
E
PA
US
E
PA
US
E
MU
TE
MU
TE
MU
TE
MU
TE
V V V VOOOOL
L L L++++
PR
EV
PR
EV
PR
EV
PR
EV
CH
AN
CH
AN
CH
AN
CH
AN
CO
D
E
CO
D
E
CO
D
E
CO
D
E
SE
A
RC
H
SE
A
RC
H
SE
A
RC
H
SE
A
RC
H
AUDI
O
1
AUDI
O
1
AUDI
O
1
AUDI
O
1
AUXAUXAUXAUX
SE
TU
P
QU
IT
MO
D
E
SL
EEP
SSSSCCCCA
AAANNNN
CH
A
PT
ER
/CH
CH
A
PT
ER
/CH
CH
A
PT
ER
/CH
CH
A
PT
ER
/CH
++++
RE
PE
AT
RE
PE
AT
RE
PE
AT
RE
PE
AT
SSSSCCCCA
AAANNNN
++++
CCCCHHHHA
AAAPPPPT
TTTEEEER
RRR////CCCCH
HHH
touching anywhere on the LCD turns the display on. The remaining rubber
buttons do not activate the display
.
The Code Search button is used for setting up the remote. The red indicator
(LED) blinks briefly when you press the Code Search button. T
o
enter the
Setup routines press and hold the Code Search button until the LED remains
on. The Main Setup Screen shown below appears. Setup is used for direct
Library Code entry
, Code Searching, Code Identification., etc. Exit from Setup
occurs automatically after 60 seconds if no button is pressed. In certain
labels, shown below
.
Y
our LCD Universal Remote requires 4 new AAA alkaline batteries.
T
o
install the batteries:
1.
T
urn the remote over
, pull on the tab and lift the cover of
f.
2.
Insert the batteries, matching the batteries to the (+) and (-) marks inside
the battery compartment.
3.
Slide the battery cover back into place.
Battery Saver
Y
our LCD remote automatically “times-out” if the buttons are depressed for
more than about 30 seconds. This saves your batteries should your remote get
stuck in a place where the buttons remain depressed (e.g., between the sofa
cushions).
Code Saver
All programmed information is retained while changing batteries.
Power-On Default
When you first insert the batteries your LCD remote always powers-on in TV
Mode.
LCD
The Liquid Crystal Display (LCD) acts as a “V
irtual Keypad.” The display has
a 15 position segmented button area. The display is normally blank when the
remote is not in use. Pressing the Code Search button, any Mode button, or
Batter
y Installation
Used for
setting up
the remote.
Code Sear
c
h
Button
routines, the Code Search button can be used to return to the Main Setup
Screen. If any operation was not complete when the time-out occurs then that
operation remains unchanged at its original setting.
Notes
1.
Pressing the LCD
QUIT
button when shown in a Setup routine, returns the
display to Main Setup Screen. Any changes made prior to that point are
discarded.
2.
Y
ou can exit to normal operation by pressing the LCD
QUIT
button at the
Main Setup Screen.
3.
In some cases, pressing the Code Search button at any time in a Setup
Only shown
in TV Mode
Main Setup Scr
een
PM8TSMD.p65
12/9/02, 4:53 PM
4-5