EN 5
3139 785 32970
2.
Precautions
2) Read and comply with all caution and safety
related notes on or inside the cabinet, or on the
chassis.
3) Design Alteration Warning-Do not alter or add
to the mechanical or electrical design of this
instrument.
Design alterations and additions, including but not
limited to, circuit modifications and the addition of
items such as auxiliary audio output connections,
might alter the safety characteristics of this
instrument and create a hazard to the user. Any
design alterations or additions will make you, the
servicer, responsible for personal injury or property
damage resulting therefrom.
4) Observe original lead dress. Take extra care to
assure correct lead dress in the following areas:
(1) near sharp edges, (2) near thermally hot parts
(be sure that leads and components do not touch
thermally hot parts), (3) the AC supply, (4) high
voltage, and (5) antenna wiring. Always inspect in
all areas for pinched, out-of-place, or frayed wiring,
Do not change spacing between a component and
the printed-circuit board. Check the AC power cord
for damage.
5) Components, parts, and/or wiring that appear to
have overheated or that are otherwise damaged
should be replaced with components, parts and/ or
wiring that meet original specifications.
Additionally, determine the cause of overheating
and/or damage and, if necessary, take corrective
action to remove any potential safety hazard.
6) Product Safety Notice-Some electrical and
mechanical parts have special safety-related
characteristics which are often not evident from
visual inspection, nor can the protection they give
necessarily be obtained by replacing them with
components rated for higher voltage, wattage, etc.
Parts that have special safety characteristics are
identified by shading, an ( )or a ( )on schematics
and parts lists. Use of a substitute replacement
that does not have the same safety characteristics
as the recommended replacement part might
create shock, fire and/or other hazards. Product
safety is under review continuously and new
instructions are issued whenever appropriate.
Precautions
Содержание BDP7100/12
