background image

Warning:

1. Plug out to disconnect from power supply; Do not plug in line.

 

2. Do not exceed the max rating 

Disposal

 

This marking indicates that this product should not be disposed with 

other household wastes throughout the EU. To prevent possible harm to

the environment or human health from uncontrolled waste disposal, 

recycle it responsibly to promote the sustainable reuse of material 

resources. To return your used device, please use the return and 

collection systems or contact the retailer where the product was 

purchased. They can take this product for environmental safe recycling.

Company of License Holder

Philio Technology Corporation

Address of License Holder

8F.,No.653-2,Zhongzheng Rd., Xinzhuang Dist., New 

Taipei City 24257,Taiwan(R.O.C)

  

FCC Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital de-

vice, pursuant to Part 15 of the FCC Rules. 

These limits are designed to provide reasonable protection against harmful interference in a 

residential installation. 

This equipment generates, uses and can radiate radio frequency energy and, if not installed 

and used in accordance with the instructions, may cause harmful interference to

radio communications. 

However, there is no guarantee that interference will not occur in a particular installation. 

If this equipment does cause harmful interference to radio or television reception, which

can be determined by turning the equipment off and on, the user is encouraged to try to cor-

rect the interference by one of the following measures:

• 

Reorient or relocate the receiving antenna.

• 

Increase the separation between the equipment and receiver.

• 

Connect the equipment into an outlet on a circuit different from that to which the receiver is 

connected.

• 

Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject

to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause 

undesired operation.

FCC Caution: Any changes or modifications not expressly approved by the party responsible 

for compliance could void the user's authority to operate this equipment.

This transmitter must not be co-located or operating in conjunction with any other antenna or

transmitter.

12

Содержание PAN03













Отзывы: