PFlow Industries P118i Скачать руководство пользователя страница 2

Страница: 2 / 50

P118i Ultrasonic Flowmeter and Analyzer

Reversion: 3.0.0

Page 2 of 49

Notice

Thank you for choosing the P118i Ultrasonic Flowmeter and Analyzer with ARM chip and low-voltage

wide-pulse sending technology.

This instruction manual contains important information. Please read it carefully before operation the flowmeter

thus avoiding damage to the flowmeter from improper use.

This instruction manual will advise how to use the flowmeter step-by-step manner, including product component

description, installation, wiring and quick setup etc. to make it easier to operate.

A working knowledge of the menu settings will assist you in understanding the flowmeters

’

powerful and output

function.

Warning

May cause injury.

Attention

May damage the flow meter.

Some of the instructions may be different from the flowmeter and analyzer you have purchased. That depends on

the configuration requirements. It also may be due to changes in product design, modification and upgrade .You

will find the flowmeter display interface intuitive and easy to understand and it shall prevail when there is no

indication of the instructions. Please refer to the version number and the appendix for more information.

Содержание P118i



















































Результаты поиска

Содержание P118i

Отзывы:

Похожие инструкции для P118i

Бренды по названию

Популярные бренды

PFlow Industries P118i, Руководство пользователя

Результаты поиска

Содержание P118i

Отзывы:

Похожие инструкции для P118i

Бренды по названию

Популярные бренды