background image

8

Safety

The vacuum pump may only be used to generate a vacuum.

Only operate the turbopump with an approved backing pump.

2.4

Improper use

Improper use will cause all claims for liability and warranties to be forfeited. Improper use 
is defined as usage for purposes deviating from those mentioned above, especially:

installation of the pump with unspecified mounting material

pumping of corrosive or explosive media

pumping of condensing vapors

pumping of liquids

pumping of dusts

operation with improper high gas throughput

operation with improper high fore-vacuum pressures

operation with improper gas mode

operation with improper high levels of insulated heat input

operation in improper high magnetic fields

venting with improper high venting rates

use of the vacuum pump to generate pressure

operation of the devices in areas with ionizing radiation

operation in potentially explosive areas

use of the devices in systems in which impact-like stress and vibrations or periodic 
forces affect the devices

use of accessories or spare parts, which are not named in this manual

warranty seal

Closure seal

The product is sealed at the factory. Damaging or removal of a closure seal leads to the 
loss of liability and warranty entitlements.

Do not open the product within its warranty period!

For process-related shorter maintenance intervals please contact the Pfeiffer Vacu-
um Service.

Содержание HiPace 400












































Отзывы: