PF FF9000 Скачать руководство пользователя

Страница: 25 / 34

ELECTRICAL ERRORS

CAUSE

CORRECTION

Blank screen on Panel but power to other devices

in the control panel

Door switch circuit not making

Press door switch in and check Panel screen

Panel has developed an electrical fault or had a

power spike or blown on board fuses

Change fuses or panel MAKE SURE that the

panel is run through a MCB 14 amp breaker

gate does not run (stays open)

Check panel is showing no F Codes or E codes

Power down then back up press and hold “stop”

key to reset

Loop detector is faulting or sensing presence

Clear obstacle or reset the detector

Check panel settings have not been altered

Set P.990=1 then P.991=0101

gate staying up in raise position

Access control giving a constant pulse shorten

this

Photo cell batteries (if ﬁtted)

Check that the ﬁtted batteries still have power to
them. They should only be replaced with special

3.6V Lithium-ion batteries made for purpose. These

can be provided by your supplier

Photo cells dirty (if ﬁtted)

Clean photo cells make sure they are debris free

Mains on but no power

Isolator fuse

Check and meter fuse in isolator

gate not going up

Access control may be faulty

Remove and check gate function via the Panel

buttons

gate Staying up

Car has driven oﬀ before clearing the loop panel

is conﬁgured without “no passage” timer.

Complete cycle by going through the ground loop

“

e.211

” displaying on screen

gate door is open

Close door or check switch for faults

gate staying open and not closing

If photo-cells ﬁtted then batteries may have

expired

Check and if needed replace batteries

Faulty loop detector

Check & set or replace faulty unit

gate does not have loops ﬁtted or these have

been removed

Call the technical department for assistance the

program/wiring needs to change

Key switch left in open position

Put the switch back into the “Auto” position

Permanent supply/signal to the raise terminals

Check wiring to terminal blocks remove any

access control try again

gate programmed for safety only or gate is on a

timer

Contact your supplier for a program modifacation

chip

Troubleshooting Guide

Parking and access control equipment manufactured in the UK

Automatic Sliding Gates

Содержание FF9000



































Результаты поиска

Содержание FF9000

Отзывы:

Похожие инструкции для FF9000

Бренды по названию

Популярные бренды

PF FF9000, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание FF9000

Отзывы:

Похожие инструкции для FF9000

Бренды по названию

Популярные бренды