background image

Troubleshooting Guide

in

Parking and access control equipment manufactured in the UK

Automatic Sliding Gates

13

Please note:gate moves only in “dead-man” mode if you have any of the messages

marked above (with this symbol:

*

) shown on the display

!

 

Message 

Short description: 

Cause of message

 

I.080 

Service counter will run off 

 

I.100 

Speed in open position to high 

 

I.150 

Speed in close position to high 

 

I.160 

Permanent open command still active 

 

I.161 

Priority not active 

 

I.170 

Forced opening active 

 

I.180 

Wait for foil key command 

 

I.199 

Door counter wrong 

 

I.200 

New reference position taken over 

 

I.201 

Reference position new initialized 

 

I.205 

Synchronisation done 

 

I.210 

Limit switch not plausible 

 

I.211 

Limit switch not plausible 

 

I.200 

Reference corrected 

 

I.205 

Reference position encoder 

 

I.310 

Open command to door 2 

 

I.320 

Obstacle during opening 

 

I.325 

Obstacle during closing 

 

I.360 

Disturbed N.C. safety edge 

 

I.363 

Disturbed N.O. safety edge 

 

I.510 

Correction drive finished 

 

I.515 

Active correction drive 

 

I.520 

Pre set speed for open or close drive not reached 

 

I.555 

Measuring rotation factor not ready 

 

E.000 

"Open on Keypad pressed" 

• Stuck button or cable not connected correctly 

E.050 

"Stop on Keypad pressed " 

• Stuck button or cable not connected correctly 

E.090 

"Close on Keypad pressed " 

• Stuck button or cable not connected correctly 

E.101 

"Input 1 active" 

• Permanent Stop Signal 

E.102 

"Input 2 active " 

• Permanent Open Signal 

E.103 

"Input 3 active " 

• Permanent Close Signal 

E.104 

"Input 4 active " 

• Lower “close” limit has made 

E.105 

"Input 5 active " 

• Upper “open” limit has made 

E.106 

"Input 6 active " 

• Photo-Cell or other safety device active 

E.107 

"Input 7 active " 

• Photo-Cell or other safety device active 

E.108 

"Input 8 active " 

• This input has been activated by connected device 

E.211 

"E-Stop Ext" 

• Barrier door safety switch open* 

E.360 

"Safety Edge Tripped" 

• Faulty safety edge or edge is being pressed* 

E.501 

"Loop Ch1" 

• Presence on safety loop “Channel 1”* 

E.502 

"Loop Ch2" 

• Presence on auto loop “Channel 2”* 

Содержание FF9000



































Отзывы: