PEUGEOT Satelis 400 Скачать руководство пользователя страница 39

Страница: 39 / 84

BODY PANELS

Reproduction or translation, even partial, is forbidden without the written consent of Peugeot Motocycles

Removal of the rear shield panel

- Remove the ignition key.
- Remove the tank cover panel. See:

Procedure 5. Page: 34

- Remove the front top cover panel. See:

Procedure 7. Page: 35

- Remove:

• The ignition switch trim.
• The handlebar upper fairing (8 screw) (1).

- On each side remove:

• 2 plastic screws that secure the front leg

shield to the underbody cover.

• 2 plastic screws that secure the footboard to

the underbody cover.

- Push aside the underbody cover to reach the

screw that secures the front shield panel. (2)

- On each side remove:

• 6 plastic screws. (3)
• 2 washer head screws. Ø6 mm. (4)

Содержание Satelis 400





















































































Результаты поиска

Содержание Satelis 400

Отзывы:

Похожие инструкции для Satelis 400

Бренды по названию

Популярные бренды

PEUGEOT Satelis 400, Руководство по ремонту

Результаты поиска

Содержание Satelis 400

Отзывы:

Похожие инструкции для Satelis 400

Бренды по названию

Популярные бренды