PEUGEOT Satelis 400 Скачать руководство пользователя страница 41

Страница: 41 / 84

BODY PANELS

Reproduction or translation, even partial, is forbidden without the written consent of Peugeot Motocycles

Removal of the instrument cluster

- Remove:
- The front top cover panel. See: Procedure 7.

Page: 35
• The wind deflector.
• The handlebar upper fairing.

- On each side remove:

• 1 plastic screw. (1)
• 1 washer head screw. Ø5 mm. (2)
• 1 washer head screw. Ø6 mm. (3)

- Press the locking system (1) to actuate the

positioning lever (2) of the instrument cluster's
connector.

- Push the lever all the up (A) in order to remove

the connector from the instrument cluster.

- Remove the instrument cluster fairing.

Note: When connecting, the lever must be

pushed all the way to (A) in order not
to damage the connector.

Содержание Satelis 400





















































































Результаты поиска

Содержание Satelis 400

Отзывы:

Похожие инструкции для Satelis 400

Бренды по названию

Популярные бренды

PEUGEOT Satelis 400, Руководство по ремонту

Результаты поиска

Содержание Satelis 400

Отзывы:

Похожие инструкции для Satelis 400

Бренды по названию

Популярные бренды