Perkins 904D-E28T Скачать руководство пользователя страница 87 | Manualshive

Страница: 87 / 110

Perkins 904D-E28T Скачать руководство пользователя страница 87

• Check the movement of the yellow core when the

engine is accelerated to the engine rated speed.
The yellow core should latch at the greatest
vacuum that is attained.

If the service indicator does not reset easily, or if the
yellow core does not latch at the greatest vacuum,
the service indicator should be replaced. If the new
service indicator will not reset, the hole for the service

indicator may be restricted.

The service indicator may need to be replaced
frequently in environments that are severely dusty.

i07819526

Engine

Air

Precleaner

-

Check/

Clean

Illustration 44

g01453058

Typical engine air precleaner

(1) Wing nut
(2) Cover
(3) Body

Remove wing nut (1) and cover (2). Check for an
accumulation of dirt and debris in body (3). Clean the
body, if necessary.

After cleaning the precleaner, install cover (2) and
wing nut (1).

Note:

When the engine is operated in dusty

conditions, more frequent cleaning is required.

Do not tap or strike the air cleaner element.

i07819538

Engine

Mounts

-

Inspect

Note:

The

engine

mounts

may

not

have

been

supplied

by

Perkins.

Refer

to

the

Original

Equipment

Manufacturer

(OEM)

information

for

further

details

on

the

engine

mounts

and

the

correct

bolt

torque.

Inspect

the

engine

mounts

for

deterioration

and

for

correct

bolt

torque.

Excessive

engine

vibration

can

be

caused

by

the

following

conditions:

• Incorrect mounting of the engine

• Deterioration of the engine mounts

• Loose engine mounts

Any engine mount that shows deterioration should be
replaced. Refer to the OEM information for the
recommended torques.

When the engine mounts are supplied by Perkins the
maintenance procedure will be supplied in the
Disassembly and Assembly manual for your engine.

i08055063

Engine

Oil

Level

-

Check

Hot oil and hot components can cause personal
injury. Do not allow hot oil or hot components to
contact the skin.

NOTICE

Perform this maintenance with the engine stopped.

Note:

Ensure that the engine is either level or that

the engine is in the normal operating position to
obtain a true level indication.

NOTICE

Do not overfill the crankcase. Engine damage can
result.

M0108133-04

87

Maintenance Section

Engine Air Precleaner - Check/Clean

«
...
85
86
87
88
89
...
»

Содержание 904D-E28T















































































































Отзывы:

Нет отзывов