Perkins 904D-E28T Скачать руководство пользователя страница 84 | Manualshive

Страница: 84 / 110

Perkins 904D-E28T Скачать руководство пользователя страница 84

4.

Clean the cooling system filler cap. Inspect the

gasket that is on the cooling system filler cap. If
the gasket that is on the cooling system filler cap is
damaged, discard the old cooling system filler cap
and install a new cooling system filler cap. If the
gasket that is on the cooling system filler cap is not
damaged, pressure test the cooling system filler
cap. The correct pressure for the cooling system
filler cap is stamped on the face of the cooling
system filler cap. If the cooling system filler cap
does not retain the correct pressure, install a new
cooling system filler cap.

5.

Start the engine. Inspect the cooling system for

leaks and for proper operating temperature.

i07925186

Coolant

Level

-

Check

Pressurized System: Hot coolant can cause seri-
ous burns. To open the cooling system filler cap,
stop the engine and wait until the cooling system
components are cool. Loosen the cooling system
pressure cap slowly in order to relieve the

pressure.

Check the coolant level when the engine is stopped
and cool.

NOTICE

When any servicing or repair of the engine cooling
system is performed, the procedure must be per-
formed with the engine on level ground. This proce-
dure will allow you to check accurately the coolant
level. This procedure will also help in avoiding the risk
of introducing an air lock into the coolant system.

1.

Remove the cooling system filler cap slowly to

relieve pressure.

2.

Maintain the coolant level at the maximum mark

that is correct for your application. If the engine is
equipped with a sight glass, maintain the coolant
level to the correct level in the sight glass.

Illustration 41

g02590196

Typical filler cap gaskets

3.

Clean the cooling system filler cap and check the

condition of the filler cap gaskets. Replace the
cooling system filler cap if the filler cap gaskets are
damaged. Reinstall the cooling system filler cap.

4.

Inspect the cooling system for leaks.

i02151646

Driven

Equipment

-

Check

Refer

to

the

OEM

specifications

for

more

information

on

the

following

maintenance

recommendations

for

the

driven

equipment:

• Inspection

• Adjustment

• Lubrication

• Other maintenance recommendations

Perform any maintenance for the driven equipment
which is recommended by the OEM.

84

M0108133-04

Maintenance Section
Coolant Level - Check

«
...
82
83
84
85
86
...
»

Содержание 904D-E28T















































































































Отзывы:

Нет отзывов