manualshive.com logo in svg

Perkins 4012TESI Series, Руководство пользователя, Страница: 6 / 57

Поделиться
Скачать
Perkins 4012TESI Series Скачать руководство пользователя страница 6

BRIEF DESCRIPTION OF THE 4012/16 GAS ENGINES

4

4012/16 Gas, February 1998

4012TESI
(MINNOX)

12 cylinder, ‘V’ form, 4 stroke, gas engine, water cooled,
turbo-charged, water cooled charge air cooler with separate water
pump and cooling circuit, lean burn, low NOx emission levels, 9.5:1
compression ratio

4012TESI
(MINNOX) 200 L.C.

12 cylinder, ‘V’ form, 4 stroke, gas engine, water cooled,
turbo-charged, water cooled charge air cooler with separate water
pump and cooling circuit, lean burn, with NOx emission of less than
200 g/GJ, 9.5:1 compression ratio.

4012TESI
(MINNOX) 140 L.C.

12 cylinder, ‘V’ form, 4 stroke, gas engine, water cooled,
turbo-charged, water cooled charge air cooler with separate water
pump and cooling circuit, lean burn, with NOx emission of less than
140 g/GJ, 9.5:1 compression ratio.

4012TESI
(MINNOX) 140 H.C.

12 cylinder, ‘V’ form, 4 stroke, gas engine, water cooled,
turbo-charged, water cooled charge air cooler with separate water
pump and cooling circuit, lean burn, with NOx emission of less than
140 g/GJ, 11.5:1 compression ratio.

4016TESI
(MINNOX) 200 L.C.

16 cylinder, ‘V’ form, 4 stroke, gas engine, water cooled,
turbo-charged, water cooled charge air cooler with separate water
pump and cooling circuit, lean burn, with NOx emission level of 200
g/GJ or less, 9.5:1 compression ratio.

4016TESI
(MINNOX) 140 L.C.

16 cylinder, ‘V’ form, 4 stroke, gas engine, water cooled,
turbo-charged, water cooled charge air cooler with separate water
pump and cooling circuit, lean burn, with NOx emission of 140 g/
GJ or less, 9.5:1 compression ratio.

4016TESI
(MINNOX) 140 H.C.

16 cylinder, ‘V’ form, 4 stroke, gas engine, water cooled,
turbo-charged, water cooled charge air cooler with separate water
pump and cooling circuit, lean burn, with NOx emission of 140 g/
GJ or less, 11.5:1 compression ratio.

4016TESI
(MINNOX) 90 H.C.

16 cylinder, ‘V’ form, 4 stroke, gas engine, water cooled,
turbo-charged, water cooled charge air cooler with separate water
pump and cooling circuit, lean burn, with NOx emission of 90 g/GJ
or less, 11.5:1 compression ratio.

Содержание 4012TESI Series


























































Отзывы:

Нет отзывов