Perkins 4008-30 SD8 Скачать руководство пользователя страница 3

Страница: 3 / 42

Table of Contents

Fuel System Operation ..........................................4
Fuel Injector Mechanism........................................4

Air Inlet and Exhaust System

Air Inlet and Exhaust System .................................5
Valve Mechanism ..................................................5

Lubrication System

Lubrication System ...............................................7

Cooling System

Cooling System ....................................................9

Basic Engine

Cylinder Block, Liners and Heads .........................10
Pistons, Rings and Connecting Rods ...................10
Crankshaft ......................................................... 11
Camshaft ........................................................... 11

Electrical System

Electrical System ................................................12

Testing and Adjusting Section

Electronic Control System

Engine Governing - Adjust ...................................16

Fuel System

General Information (Fuel System) (Diesel)...........17
Fuel System Inspection .......................................17
Checking Engine Cylinders ..................................17

Air Inlet and Exhaust System

Valve Lash - Adjust..............................................18
Turbocharger ......................................................20

Lubrication System

General Information (Lubrication System) .............23
Engine Oil Pressure - Test ...................................23
Excessive Bearing Wear - Inspect ........................24
Excessive Engine Oil Consumption - Inspect.........25
Increased Engine Oil Temperature - Inspect ..........25
Engine Oil Pressure is Low ..................................25
Engine Oil Pressure is High .................................26

Cooling System

General Information (Cooling System) ..................28
Visual Inspection.................................................29
Water Temperature Regulator - Test .....................29

Basic Engine

Connecting Rod Bearings ....................................31
Main Bearings.....................................................31
Cylinder Block.....................................................31
Cylinder Head .....................................................31

Flywheel - Inspect ...............................................33
Flywheel Housing - Inspect ..................................34
Crankshaft Thrust - Measure................................35
Vibration Damper ................................................36
Gear Group (Front)..............................................37

Electrical System

Battery ...............................................................38
Charging System ................................................38
Electric Starting System.......................................38

Index Section

Index..................................................................40

M0064276

Table of Contents

Содержание 4008-30 SD8










































Результаты поиска

Содержание 4008-30 SD8

Отзывы:

Похожие инструкции для 4008-30 SD8

Бренды по названию

Популярные бренды

Perkins 4008-30 SD8, Эксплуатация систем, испытания и настройка

Результаты поиска

Содержание 4008-30 SD8

Отзывы:

Похожие инструкции для 4008-30 SD8

Бренды по названию

Популярные бренды