Perkins 4008-30 SD8 Скачать руководство пользователя страница 37

Страница: 37 / 42

i06515929

Gear

Group

(Front)

Illustration 27

g06005826

Typical example

(1) Idler gear
(2) Camshaft gear
(3) Crankshaft gear
(4) Oil Pump Gear

Inspect the gears for wear or for damage. If the

gears are worn or damaged, use new parts for
replacement.

Make sure that the timing marks on the gears (1),

(2), (3) and (4) are in alignment.

Measure the backlash between idler gear (1) and

oil pump gear (4). Refer to Specifications, “Gear
Group (Front)” for the backlash measurement.

Measure the backlash between oil pump gear (4)

and crankshaft gear (3). Refer to Specifications,
“Gear Group (Front)” for the backlash
measurement.

Measure the backlash between idler gear (1) and

crankshaft gear (3). Refer to Specifications, “Gear
Group (Front)” for the backlash measurement.

Measure the backlash between camshaft gear (2)

and idler gear (1). Refer to Specifications, “Gear
Group (Front)” for the backlash measurement.

M0064276

Basic Engine

Содержание 4008-30 SD8










































Результаты поиска

Содержание 4008-30 SD8

Отзывы:

Бренды по названию

Популярные бренды

Perkins 4008-30 SD8, Эксплуатация систем, испытания и настройка

Результаты поиска

Содержание 4008-30 SD8

Отзывы:

Бренды по названию

Популярные бренды