Perkins 2806C-E18TA Скачать руководство пользователя страница 81 | Manualshive

Страница: 81 / 104

Perkins 2806C-E18TA Скачать руководство пользователя страница 81

Illustration 51

g06095752

5.

Ensure that the oil filter housing (4) is clean and

free from dirt. Install the new filter element (2) into
the oil filter housing (4). To insure correct
orientation of the oil filter element (2), the molding
(6) on filter element (2) must be installed into
molding (7) in the oil filter housing (4).

6.

Install a new oil ring seal (3) on to the oil filter

housing (4) and lubricate the O ring (3) with clean
engine oil.

7.

Install oil filter assembly (4) into filter base (1) and

tighten to a torque of 80 N·m (59 lb ft).

2806D Replace the Oil Filters

1.

Remove the oil filters with a suitable tool.

Illustration 52

g03860982

2.

Clean sealing surfaces (1).

3.

Apply clean engine oil to O ring seals (2) for the

new oil filters (3).

NOTICE

Do not fill the oil filters with oil before installing. This
oil would not be filtered and could be contaminated.

Contaminated oil can cause accelerated wear to en-

gine components.

4.

Install the new oil filters (3). Spin on the oil filter

until the O rings contacts the sealing surfaces (2).
Then rotate the oil filters one full turn. Remove the
container and disposal of the waste oil in
accordance with local regulations.

Fill the Oil Pan

1.

Remove the oil filler cap. Refer to this Operation

and Maintenance Manual, “Fluid
Recommendations” for more information on
suitable oils. Fill the oil pan with the correct
amount of new engine lubricating oil. Refer to this
Operation and Maintenance Manual, “Refill
Capacities” for more information on refill
capacities.

2.

Start the engine and run the engine for 2 minutes.

Perform this procedure to ensure that the
lubrication system has oil and that the oil filters are
filled. Inspect the oil filters for oil leaks.

3.

Stop the engine and allow the oil to drain back to

the oil pan for a minimum of 10 minutes.

SEBU9074-01

81

Maintenance Section

Engine Oil and Filter - Change

«
...
79
80
81
82
83
...
»

Содержание 2806C-E18TA









































































































Отзывы:

Нет отзывов