manualshive.com logo in svg

Perkins 2806C-E18TA, Руководство по эксплуатации и обслуживанию, Страница: 69 / 104

Поделиться
Скачать
Perkins 2806C-E18TA Скачать руководство пользователя страница 69

2.

Open the cooling system drain valve.

Allow the coolant to drain.

Flush

1.

Flush the cooling system with clean water and a

suitable cleaning agent in order to remove any
debris. Refer to your Perkins distributor for
suitable cleaning agents.

2.

Close the cooling system drain valve.

NOTICE

Do not fill the cooling system faster than 5 L
(1.3 US gal) per minute to avoid air locks.

Cooling system air locks may result in engine
damage.

3.

Fill the cooling system with clean water and install

the cooling system filler cap.

4.

Start and run the engine until normal operating

temperature.

5.

Stop the engine and allow the engine to cool.

Loosen the cooling system filler cap slowly in
order to relieve any pressure. Remove the cooling
system filler cap. Open the cooling system drain
valve. Allow the water to drain. Flush the cooling
system with clean water.

6.

Close the cooling system drain valve.

Fill

NOTICE

Fill the cooling system no faster than 19 L (5 US gal)
per minute to avoid air locks.

1.

Fill the cooling system with coolant/antifreeze.

Refer to this Operation and Maintenance Manual,
“Fluid Recommendations” topic for more
information on cooling system specifications. Do
not install the cooling system filler cap.

2.

Start and run the engine at low idle. Increase the

engine rpm to 1500 rpm. Run the engine at high
idle for 1 minute in order to purge the air from the
cavities of the engine block. Stop the engine.

3.

Check the coolant level. Maintain the coolant level

within 13 mm (0.5 inch) below the bottom of the
pipe for filling. Maintain the coolant level within
13 mm (0.5 inch) to the proper level on the sight
glass.

4.

Clean the cooling system filler cap. Inspect the

gasket that is on the cooling system filler cap. If
the gasket that is on the cooling system filler cap is
damaged, discard the old filler cap and install a
new filler cap. If the gasket that is on the cooling
system filler cap is not damaged, perform a
pressure test. The correct pressure for the cooling
system filler cap is stamped on the face of the
cooling system filler cap. If the cooling system filler
cap does not retain the correct pressure, install a
new cooling system filler cap.

5.

Start the engine. Inspect the cooling system for

leaks and for proper operating temperature.

i06221440

Coolant

 

(ELC)

 

-

 

Change

 

NOTICE

Perkins ELC must be using with an extender in order
to achieve 12000 hours operation. For more informa-
tion on a suitable extender contact your Perkins
distributor.

Clean the cooling system and flush the cooling
system before the recommended maintenance
interval if the following conditions exist:

• The engine overheats frequently.

• Foaming is observed.

• The oil has entered the cooling system and the

coolant is contaminated.

• The fuel has entered the cooling system and the

coolant is contaminated.

Note:

When the cooling system is cleaned, only

clean water is needed when the ELC is drained and
replaced.

Note:

Inspect the water pump and the water

temperature regulator after the cooling system has
been drained.

SEBU9074-01

69

Maintenance Section

Coolant (ELC) - Change

Содержание 2806C-E18TA









































































































Отзывы:

Нет отзывов