Perkins 2806C-E18TA Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 104

Perkins 2806C-E18TA Скачать руководство пользователя страница 12

Exhaust shields (if equipped) protect hot exhaust
components from oil or fuel spray in case of a line, a
tube, or a seal failure. Exhaust shields must be

installed correctly.

Do not weld on lines or tanks that contain flammable

fluids. Do not flame cut lines or tanks that contain

flammable fluid. Clean any such lines or tanks
thoroughly with a nonflammable solvent prior to
welding or flame cutting.

Wiring must be kept in good condition. Ensure that all
electrical wires are correctly installed and securely
attached. Check all electrical wires daily. Repair any
wires that are loose or frayed before you operate the
engine. Clean all electrical connections and tighten
all electrical connections.

Eliminate all wiring that is unattached or
unnecessary. Do not use any wires or cables that are
smaller than the recommended gauge. Do not
bypass any fuses and/or circuit breakers.

Arcing or sparking could cause a fire. Secure
connections, recommended wiring, and correctly
maintained battery cables will help to prevent arcing
or sparking.

Ensure that the engine is stopped. Inspect all lines
and hoses for wear or for deterioration. Ensure that

the hoses are correctly routed. The lines and hoses
must have adequate support and secure clamps.

Oil filters and fuel filters must be installed correctly.
The filter housings must be tightened to the correct
torque. Refer to the Disassembly and Assembly
manual for more information.

Illustration 11

g00704059

Use caution when you are refueling an engine. Do
not smoke while you are refueling an engine. Do not
refuel an engine near open flames or sparks. Always
stop the engine before refueling.

Avoid static electricity risk when fueling. Ultra-low
Sulfur Diesel fuel (ULSD fuel) poses a greater static
ignition hazard than earlier diesel formulations with a
higher sulfur content. Avoid death or serious injury
from fire or explosion. Consult your fuel or fuel
system supplier to ensure that the delivery system is
in compliance with fueling standards for proper
grounding and bonding practices.

Illustration 12

g00704135

Gases from a battery can explode. Keep any open
flames or sparks away from the top of a battery. Do
not smoke in battery charging areas.

Never check the battery charge by placing a metal
object across the terminal posts. Use a voltmeter or a
hydrometer.

Incorrect jumper cable connections can cause an
explosion that can result in injury. Refer to the
Operation Section of this manual for specific
instructions.

Do not charge a frozen battery. A frozen battery may
cause an explosion.

The batteries must be kept clean. The covers (if
equipped) must be kept on the cells. Use the
recommended cables, connections, and battery box
covers when the engine is operated.

12

SEBU9074-01

Safety Section
Fire Prevention and Explosion Prevention

«
...
10
11
12
13
14
...
»

Содержание 2806C-E18TA









































































































Отзывы:

Нет отзывов