Perkins 2806C-E18TA Скачать руководство пользователя страница 68

Страница: 68 / 104

If new drive belts are installed, check the drive belt

tension again after 30 minutes of engine operation
at the rated rpm.

Adjustment of the Fan Drive Belts

Illustration 37

g06109234

Typical example

Remove the belt guard, refer to OEM for the

correct procedure.

Loosen lock nut (3). Rotating nut (4) counter-

clockwise will move pulley (1) and loosen belts (2).
Rotating nut (4) clockwise will move pulley (1) and
tighten belts (2).

With the correct tension set, tighten nut (3).

Tighten nut (3) to a torque of 102 N·m (75 lb ft).

Use a suitable belt tension tool to set the belt

tension.

Reinstall the belt guard, refer to OEM for the

correct procedure.

If new drive belts are installed, check the drive belt

tension again after 30 minutes of engine operation
at the rated rpm.

i06221395

Coolant (DEAC) - Change

Clean the cooling system and flush the cooling
system before the recommended maintenance
interval if the following conditions exist:

• The engine overheats frequently.

• Foaming is observed.

• The oil has entered the cooling system and the

coolant is contaminated.

• The fuel has entered the cooling system and the

coolant is contaminated.

Note:

Inspect the water pump and the water

temperature regulator after the cooling system has
been drained.

Illustration 38

g02351659

Typical example of a cooling system drain valve. The
valve is towards the bottom of the radiator.

Drain

Pressurized System: Hot coolant can cause seri-
ous burns. To open the cooling system filler cap,
stop the engine and wait until the cooling system
components are cool. Loosen the cooling system
pressure cap slowly in order to relieve the

pressure.

Stop the engine and allow the engine to cool.

Loosen the cooling system filler cap slowly in
order to relieve any pressure. Remove the cooling
system filler cap.

SEBU9074-01

Maintenance Section
Coolant (DEAC) - Change

Содержание 2806C-E18TA








































































































Результаты поиска

Содержание 2806C-E18TA

Отзывы:

Perkins 2806C-E18TA, Руководство по эксплуатации и обслуживанию, Страница: 68 / 104

Результаты поиска

Содержание 2806C-E18TA

Отзывы: