Perkins 1206E-E66TA Скачать руководство пользователя страница 88

Страница: 88 / 120

SEBU8603-01

Maintenance Section

Driven Equipment - Check

NOTICE

Failure to replace your water temperature regulator

on a regularly scheduled basis could cause severe

engine damage.

Perkins engines incorporate a shunt design cooling

system and require operating the engine with a water

temperature regulator installed.

If the water temperature regulator is installed incor-

rectly, the engine may overheat, causing cylinder head

damage. Ensure that the new water temperature reg-

ulator is installed in the original position. Ensure that

the water temperature regulator vent hole is open.

Do not use liquid gasket material on the gasket or

cylinder head surface.

Refer to two articles in the Disassembly and

Assembly Manual, “Water Temperature Regulators

- Remove and Water Temperature Regulators -

Install” for the replacement procedure of the water

temperature regulator, or consult your Perkins dealer

or your Perkins distributor.

Note:

If only the water temperature regulators are

replaced, drain the coolant from the cooling system to

a level that is below the water temperature regulator

housing.

i02151646

Driven Equipment - Check

Refer to the OEM speci

cations for more information

on the following maintenance recommendations for

the driven equipment:

•

Inspection

•

Adjustment

•

Lubrication

•

Other maintenance recommendations

Perform any maintenance for the driven equipment

which is recommended by the OEM.

i03991933

Engine - Clean

Personal injury or death can result from high volt-

age.

Moisture can create paths of electrical conductiv-

ity.

Make sure that the electrical system is OFF. Lock

out the starting controls and tag the controls “DO

NOT OPERATE”.

NOTICE

Accumulated grease and oil on an engine is a

re haz-

ard. Keep the engine clean. Remove debris and

uid

spills whenever a signi

cant quantity accumulates on

the engine.

Periodic cleaning of the engine is recommended.

Steam cleaning the engine will remove accumulated

oil and grease. A clean engine provides the following

bene

ts:

•

Easy detection of

uid leaks

•

Maximum heat transfer characteristics

•

Ease of maintenance

Note:

Caution must be used in order to prevent

electrical components from being damaged by

excessive water when the engine is cleaned.

Pressure washers and steam cleaners should not be

directed at any electrical connectors or the junction of

cables into the rear of the connectors. Avoid electrical

components such as the alternator, the starter, and

the ECM. Protect the fuel injection pump from

uids

in order to wash the engine.

Aftertreatment

During the engine cleaning process, ensure

that water or cleaning

uids cannot enter the

aftertreatment system. If cleaning

uids enters the

aftertreatment system, damage could occur.

Содержание 1206E-E66TA
























































































































Результаты поиска

Содержание 1206E-E66TA

Отзывы:

Perkins 1206E-E66TA, Руководство по эксплуатации и обслуживанию, Страница: 88 / 120

Результаты поиска

Содержание 1206E-E66TA

Отзывы: