Perkins 1206E-E66TA Скачать руководство пользователя страница 101

Страница: 101 / 120

SEBU8603-01

101

Maintenance Section

Fuel System Secondary Filter - Replace

Install a suitable tube onto drain (3). Open

the drain valve (2). Rotate the drain valve

counterclockwise. Two full turns are required.

Loosen vent screw (1).

Note:

Two complete rotations of the valve will release

the valve from the

lter element.

Allow the

uid to drain into the container.

Engage the threads of the valve into the

lter

element and tighten the drain valve by hand

pressure only. Remove the tube and remove the

container.

Tighten vent screw securely.

i04380994

Fuel System Secondary Filter -

Replace

Fuel leaked or spilled onto hot surfaces or elec-

trical components can cause a

re. To help pre-

vent possible injury, turn the start switch off when

changing fuel

lters or water separator elements.

Clean up fuel spills immediately.

NOTICE

Ensure that the engine is stopped before any servicing

or repair is performed.

Refer to Systems Operation, Testing, and

Adjusting, “Cleanliness of Fuel System

Components” for detailed information on the

standards of cleanliness that must be observed

during ALL work on the fuel system.

Remove the Element

Turn the fuel supply valve (if equipped) to the OFF

position before performing this maintenance.

Place a suitable container under the fuel

lter in

order to catch any fuel that might spill. Clean up

any spilled fuel. Clean the outside body of the

lter

assembly.

g02546439

Illustration 66
Typical example

Make a temporary Mark (A) across the

lter before

the assembly is removed. Install a suitable tube

onto drain (4). Open the drain valve (3). Rotate

the drain valve counterclockwise. Two full turns

are required. Loosen vent screw (1).

Note:

Two complete rotations of the valve will release

the valve from the

lter element.

Allow the fuel to drain into the container. Remove

the tube and install the valve into the

lter element.

Engage the threads of the valve into the

lter

element. Do not secure the valve.

Tighten the vent screw (1) securely.

Remove the

lter bowl (2). Rotate the

lter

assembly counterclockwise in order to remove the

assembly. Use a suitable tool in order to remove

the

lter bowl.

Содержание 1206E-E66TA
























































































































Результаты поиска

Содержание 1206E-E66TA

Отзывы:

Perkins 1206E-E66TA, Руководство по эксплуатации и обслуживанию, Страница: 101 / 120

Результаты поиска

Содержание 1206E-E66TA

Отзывы: