Perkins 1206E-E66TA Скачать руководство пользователя страница 100

Страница: 100 / 120

100

SEBU8603-01

Maintenance Section

Fuel System Primary Filter/Water Separator - Drain

Install the Element

g02148441

Illustration 64
Typical example

Locate the thread in the

lter element (8) onto the

threads (9). Spin on the element. Do not tighten.

Lubricate the O ring seal (7) with clean engine oil.

Do NOT

ll the bowl with fuel before the assembly

is installed.

Do not use a tool in order to install the

lter

assembly. Tighten the

lter bowl (6) by hand.

Install the

lter bowl (6) and align with your

temporary marks (A).

Tighten the valve (2) securely. Remove the

container and dispose of the fuel in a safe place.

The secondary

lter element must be replaced at

the same time as the primary

lter element. Refer

to the Operation and Maintenance Manual , “Fuel

System Filter - Replace”.

In-line Strainer

The fuel system has an in-line strainer installed before

the electric priming pump. Perkins recommended

that the in-line strainer be replaced when required.

The location of the in-line strainer will depend on the

application.

i03980098

Fuel System Primary

Filter/Water Separator - Drain

Fuel leaked or spilled onto hot surfaces or elec-

trical components can cause a

re. To help pre-

vent possible injury, turn the start switch off when

changing fuel

lters or water separator elements.

Clean up fuel spills immediately.

NOTICE

Ensure that the engine is stopped before any servicing

or repair is performed.

NOTICE

The water separator can be under suction during nor-

mal engine operation. Ensure that the drain valve is

tightened securely to help prevent air from entering

the fuel system.

Place a suitable container under the water

separator in order to catch any

uid that might

spill. Clean up any spilled

uid.

Ensure that the outer body of the

lter assembly is

clean and free from dirt.

g02148370

Illustration 65
Typical example

Содержание 1206E-E66TA
























































































































Результаты поиска

Содержание 1206E-E66TA

Отзывы:

Perkins 1206E-E66TA, Руководство по эксплуатации и обслуживанию, Страница: 100 / 120

Результаты поиска

Содержание 1206E-E66TA

Отзывы: