PerkinElmer Frontier Optica FT-IR Скачать руководство пользователя страница 84

Страница: 84 / 94

84 . Frontier Optica FT-IR User's Guide

Figure 48 Laser Board connector

Unhook the spring and remove the two screws on the retaining bracket, as shown in

Figure 49.

Figure 49 Laser and power supply installation

Remove the laser and power supply; noting the way the cabling is routed.

Install the new laser and power supply.

Ensure the laser is pushed fully home to the stop at the front of the housing.
The laser must be installed so that the yellow laser warning label is facing directly

upwards.

Refit the laser retaining bracket and secure with the two securing screws.

Secure the spring on the retaining pin.

10.

Reconnect the PSU Laser cable to the board connector.

11.

Secure the laser power supply with the two securing screws.
Make sure that the laser cabling is secured so that it does not get trapped in the cover.

12.

Close and secure the main cover.
Refer to page 74, steps 10 to 15.

NOTE:

Allow the Frontier Optica FT-IR spectrometer to equilibrate for approximately 2 hours

before using the instrument.

Laser

Laser baffle

Laser spring

retaining pin

Power supply

Laser bracket

retaining screw

Screw

Laser bracket

retaining screw

Baffle retaining screws

Connector

Содержание Frontier Optica FT-IR































































































Результаты поиска

Содержание Frontier Optica FT-IR

Отзывы:

Похожие инструкции для Frontier Optica FT-IR

Бренды по названию

Популярные бренды

PerkinElmer Frontier Optica FT-IR, Руководство пользователя

Результаты поиска

Содержание Frontier Optica FT-IR

Отзывы:

Похожие инструкции для Frontier Optica FT-IR

Бренды по названию

Популярные бренды