PerkinElmer Frontier Optica FT-IR Скачать руководство пользователя страница 79

Страница: 79 / 94

Advanced Maintenance . 79

Installing Filters in the Filter Wheel

The following procedure describes how to install a filter in the filter wheel. The same

procedure should be followed when replacing a filter or the methane cell.

The filter wheel assembly is removed from its mounting and placed on the standard sample

slide baseplate.

Set the

Filter Wheel

to the Position 1 on the Setup Instrument BeamPath tab in the

Spectrum software.
Position 1 will be labelled as

None 15000 – 0 cm

-1

and be the first option in the drop-

down list.

WARNING

Switch off the mains power supply to the spectrometer, wait 60 seconds,

and disconnect the power cable before you open the cover of the

spectrometer. This makes sure that you are safe from electrical shock

and laser radiation.

Open the main cover of the instrument as detailed on page 72 and identify the filter

wheel.

Figure 42 Filter wheel location

Filter wheel

Содержание Frontier Optica FT-IR































































































Результаты поиска

Содержание Frontier Optica FT-IR

Отзывы:

Бренды по названию

Популярные бренды

PerkinElmer Frontier Optica FT-IR, Руководство пользователя

Результаты поиска

Содержание Frontier Optica FT-IR

Отзывы:

Бренды по названию

Популярные бренды