background image

Operation manual 

18 

  Set the «Power» and «Battery» switchers on the control unit (8) in the «0» position (Fig. 3); 

  Disconnect the power cable (12) from the mains; 

  Swap positions of the following RC cables inside the control unit, on the connectors X3 

and X4 of the processor module (Fig. 9) white with green and yellow with red cable, that is 

connect the cables as follows: 

 

a) white— to contact 3 on the X3; 

 

b) green – to contact 1 on the X3; 

 

c) yellow – to contact 3 on the X4; 

 

d) red — to contact 1 on the X4; 

  check all the cable connections are correct; 

  turn the power on as per section 9.1; 

  check the operation as per section 9.2. 

Table 2. Turnstile operating mode 

  Turnstile operating 

mode 

Your actions 

Indication on 

the RC 

Indication 

outputs 

status 

Turnstile status 

Always locked  (Closed 

for entry and exit)

 

Press the 

STOP

 

button on the RC

 

The red 

indicator above 

the 

STOP 

button 

is on

 

“LED Red_L”

 

and 

“LED 

Red_R”

 

outputs are 

active

 

The barrier wings 

are in the reset 

state. The barrier 

wings rotation is 

blocked in either 

direction 

Single passage in the 

set direction (open for 

passage of one person 

in the chosen direction)

 

Press the button 

corresponding to 

the chosen 

passage direction

 

The green 

indicator above 

the button of the 

chosen passage 

direction and the 

red indicator 

above the STOP 

button are on

 

“LED Grn_L”

  

or  

“LED Grn_R”

 

output is active 

depending on 

the set 

direction

 

The barrier wings 

rotation in the set 

direction is allowed 

Bidirectional single 

passage (open for one-

by-one person passage 

in each direction)

 

Press both 

passage buttons 

simultaneously 

(left and right side 

buttons on the 

RC)

 

The two green 

indicators (left 

and right) and 

the red indicator 

above the

 STOP 

button are on

 

“LED Grn_L”

 

and  

“LED Grn_R”

 

outputs are 

active

  

The barrier wings 

rotation in one 

direction and then 

in the other 

direction is allowed

 

Free passage in the set 

direction (open for free 

passage in the chosen 

direction)

 

Press the 

STOP

 

button and the 

button 

corresponding to 

the chosen 

passage direction 

simultaneously

 

The green 

indicator above 

the button of the 

chosen passage 

direction is on

 

“LED Grn_L”

 

or  

“LED Grn_R”

 

output is active 

depending on 

the set 

direction

 

The barrier wings 

rotation in the set 

direction is allowed 

without any 

limitations

 

Free passage in the set 

direction and single 

passage in the 

opposite direction 

(open for free passage 

in the chosen direction 

and for a person’s 

passage in the 

opposite direction)  

Carry out actions 

stated in Chapters 

2 and 4 of the 

present table in 

any order 

The two green 

indicators above 

either passage 

direction and the 

red indicator 

above the

 STOP 

button are on 

“LED Grn_L”

 

and  

“LED Grn_R”

 

outputs are 

active 

The barrier wings 

rotation on the free 

passage direction 

without any 

limitations and a 

single rotation in 

the opposite 

direction are 

allowed  

Содержание RTD-03S



























Отзывы:

Похожие инструкции для RTD-03S