Pepwave 200 OfficePoint Indoor Series страница 47 Скачать руководство пользователя

Страница: 47 / 50

http://www.pepwave.com

User Manual

Pepwave OfficePoint Series

Restoration of Factory Defaults

10.1

OfficePoint Indoor Series

The following procedure restores the settings of Pepwave OfficePoint indoor device to factory defaults:

Power on the unit, wait for 1 minute until the Status LED turns green.

Press and hold the reset button on the rear panel for at least 5 seconds, then release.

The Status LED will blink, and then the unit will automatically reboot.

4. Wait for 1 minute or until the Status LED turns green, upon which the settings of Pepwave

OfficePoint will have been restored to the factory defaults.

By default, the unit will acquire an IP address from a DHCP server.

10.2

OfficePoint Outdoor Series

There are two ways to restore the Pepwave OfficePoint outdoor device to default settings.
If you are able to access the web admin interface, go to the “CPE Setup” page, and click the

Restore and

Reboot

button.

Otherwise, you can power up the unit and wait for about 1 min. Then push the

Reset Button

at the panel

side of the unit and then hold it for 5 seconds. The unit will restore the settings to factory default and

reboot.

Содержание 200 OfficePoint Indoor Series


















































Результаты поиска

Содержание 200 OfficePoint Indoor Series

Отзывы:

Похожие инструкции для 200 OfficePoint Indoor Series

Бренды по названию

Популярные бренды

Pepwave 200 OfficePoint Indoor Series, Руководство пользователя

Результаты поиска

Содержание 200 OfficePoint Indoor Series

Отзывы:

Похожие инструкции для 200 OfficePoint Indoor Series

Бренды по названию

Популярные бренды