Pepperl+Fuchs Bebco EPS 6100-MP-EX Series Скачать руководство пользователя страница 30

Страница: 30 / 60

6100 Series Manual

Note!

The following parameters must be entered for the purge time:

Enclosure volume

Number of exchanges

Type of vent for flow rate—enter flow rate

Minimum purge time is 2 min.

Fixed Purge Time

The purge time is based on the known enclosure volume, number of volume exchanges, and flow rate

through the vent. If the flow rate is below the required minimum, then the purging cycle will reset and will not

start until the flow rate is above the selected rate. This setup does not allow purge flow to go below the value

required and will not recalculate the time for purging if it goes above the required purge rate. The actual time is

calculated by the EPCU.

Purging modes

Purging start-up can be set in 3 different modes:

STD – Standard mode requires the operator to engage the manifold solenoid valve manually when

purging and manually disengage when a successful purging is complete.

SA – Semi-automatic mode requires the operator to engage the manifold solenoid valve manually when

purging. The EPCU will automatically disengage when a successful purging is complete.

FA – Fully-automatic mode will automatically engage the manifold solenoid valve when safe pressure

is detected and will automatically disengage when a successful purging is complete. This is the factory

default setting.

The minimum purge time is 2 minutes.
During the purging cycle, when the enclosure pressure reaches 0.25" wc [(6.4 mm wc) or higher, there will

be a 5 second delay before the rapid exchange solenoid valve is activated. If the flow is enough through the

vent to satisfy the required flow rate setting, then the timer will begin after 1 min. The update of the timer is in

increments of 1min in the Fixed Purge Time and % completed in the Dynamic Purge Time.

Pressure as Input

In the programming menu under "INPUT SETTINGS" for the optional pressure control. The pressure control

is achieved within the enclosure by opening and closing a purging valve or manifold on the 6100 control unit.

These two internal pressure set points are controlled by the manifold or an outside source for pressure. The

pressure function can manage the control output 2, or the control valve (manifold valve).

Operation

Содержание Bebco EPS 6100-MP-EX Series





























































Результаты поиска

Содержание Bebco EPS 6100-MP-EX Series

Отзывы:

Похожие инструкции для Bebco EPS 6100-MP-EX Series

Бренды по названию

Популярные бренды

Pepperl+Fuchs Bebco EPS 6100-MP-EX Series, Руководство пользователя

Результаты поиска

Содержание Bebco EPS 6100-MP-EX Series

Отзывы:

Похожие инструкции для Bebco EPS 6100-MP-EX Series

Бренды по названию

Популярные бренды