background image

During this process the valves will need to be quickly advanced 
to the next cycle. To quick cycle, press 

 and 

 after the 

regeneration cycle has started.
Alternating tank systems have one Logix 764 control that is 

mounted on Tank 1. Tank 2 has a blank faceplate and the Tank 

2 valve is controlled by the Logix 764 control on Tank 1.

Placing the Alternating System into Operation

1.  Press and hold the 

 button for five seconds. This will 

start the first regeneration.

NOTE:   

Once the valve has reached the cycle (visible on 

the display and camshaft has stopped turning), 

quick cycle to the next cycle. This is especially 

recommended for the C8 cycle. Overfilling the 

regenerant tank will affect the brine and future regen 

cycles.

NOTE:   

It is recommended that you do not put regenerant 

into the tank until after the control valve has been 

put into operation. With not regenerant in the tank, it 

is much easier to view water flow and motion in the 

tank.

Tank 1 moves through cycles:

C5 - Fast Rinse: as the water enters the tank, air will 

be forced out the drain line. Once water fills the tank, 

it will then discharge out the drain line. Quick cycling 

the control can now be used to advance through the 

remaining cycles.
C8 - Regenerant Refill: the aircheck is filled and flow to 

the regenerant tank is visible.
Quick cycle Tank 1 to service

then--
Tank 2 moves through cycles:

C1 - Backwash: as water enters the tank, air will be 

forced out the drain line. Once water fills the tank, it 

will then discharge out the drain line. Quick cycling 

the control can now be used to advance through the 

remaining cycles.
C2 - Regenerant Draw: the regenerant tank should 

have water in it. As the draw occurs the level will go 

down.
C3 - Slow Rinse
C4 - Standby

Both tanks have now been purged of air. The water supply 

valve can be fully opened.

2.  Press and hold the 

 button for five seconds. This will 

start the second regeneration.
Quick cycle as Tank 2 moves through cycles:

C5 - Fast Rinse
C8 - Regenerant Refill: the aircheck is filled and flow to 

the regenerant tank is visible.

then--
Quick cycle as Tank 1 moves through cycles:

C1 - Backwash
C2 - Regenerant Draw: the regenerant tank should 

have water in it. As the draw occurs the level will go 

down.
C3 - Slow Rinse
C4 - Standby

At this point Tank 1 is fully operational.

3.  Press and hold the 

 button for five seconds. This will 

start the third regeneration. After this step both tanks will 

be ready. 
Quick cycle as Tank 1 moves through cycles:

C5 - Fast Rinse
C8 - Regenerant Refill
Quick cycle to service

then--
Quick cycle as Tank 2 moves through cycles:

C1 - Backwash
C2 - Regenerant Draw: the regenerant tank should 

have water in it. As the draw occurs the level will go 

down.
C3 - Slow Rinse
C4 - Standby

Both tanks are now ready.

4.  Turn on a faucet plumbed after the water conditioner. Run 

the faucet until the water runs clear.

5.  Add water to the regenerant tanks.

A.  With a bucket or hose, add water until approximately 

four gallons (15 liters) of water in each regenerant tank.

B.  If the tank has a salt platform in the bottom of the tank, 

add water until the water level is approximately 1"(25 

mm) above the platform.

The Alternating Water Conditioning System is 

Now Fully Operational

NOTE:   

After any control reset (valve type or system 

change, etc.), it is necessary to initiate a manual 

regeneration and quick cycle through it. This will 

ensure the control and cam are synchronized. If not 

synchronized, Err3 will display and the control will 

drive cams to the correct position for the valve and 

system type programmed.

PROGRAMMING 

CONTINUED

 

AUTOTROL

®

 Logix 764 Control Performa Cv Series Valves (273, 278) Service Manual 

 

15

Содержание AUTOTROL LOGIX 764













































Отзывы: