manualshive.com logo in svg

Pentair 522352, Руководство по установке

Поделиться
Скачать
Pentair 522352 Скачать руководство пользователя страница 33

 

EASYTOUCH

® 

PL4/PSL4 Control System Installation Guide 

 

                                                                                                                    

EASYTOUCH

® 

PL4/PSL4 Control System Installation 

                                                                                                                                                                                            25 

EasyTouch PL4/PSL4 Control System QuickTouch

®

 II 

Wireless Controller Transceiver Installation

 

Installing the QuickTouch Wireless Controller Transceiver

The following procedure describes how to install the EasyTouch PL4/PSL4 Control System 
QuickTouch (QT4) Wireless Controller transceiver module and connect the transceiver cable to the 

COM port on the motherboard. Read through the installation procedure before starting. 

EasyTouch PL4/PSL4 Control System Wireless Controller kit

The EasyTouch PL4/PSL4 Control System wireless control panel kit consists of:

•  EasyTouch PL4/PSL4 wireless control panel
•  Four AA-size alkaline batteries
•  Transceiver module 
•  Four plastic anchors and retaining screws (to mount the transceiver module)

Mounting the Wireless Transceiver

The Transceiver is a two-way radio device with an attached antenna that communicates to and 
from the EasyTouch PL4/PSL4 control system via the wireless hand-held wireless control panel.  

Mount the Transceiver module at a convenience location (on a flat vertical surface) near the Power 
Center, at a minimum of 5 ft. above ground level to optimize the functional operating range of the 

wireless control panel.

 

CAUTION - 

To avoid signal interference, mount the Transceiver antenna a minimum of 

10 ft. away from the Power Center, any metal surface/structure, or air blower located in the 
immediate area of the equipment pad.

To mount the transceiver near the EasyTouch PL4/PSL4 Control System Power Center:

1. 

 

CAUTION - 

Switch the main power off at the EasyTouch PL4/PSL4 Control System 

Power Center.

2.  Remove the two retaining screws securing the transceiver case to the back plate. 

Carefully slide the case off the back plate. 

3. 

 CAUTION

 

-

 Electrostatic Discharge (ESD): Hold the circuit board from the edges. 

Do not touch the board components, electrostatic discharge can damage the board.

 

Slide the transceiver circuit board up and out of the back plate.  

4.  Position the back plate against the mounting surface so that the case is oriented in 

an upright position (with the antenna pointing upwards). Use a pencil to mark the four 
mounting points. Drill four 3/16 in. diameter holes into the mounting surface. If screws are 
not being used, insert the four plastic wall anchors (provided in the kit).

5.  Feed the provided 10 ft. of UL approved four 22 AWG conductor cable through the 

knockout hole at the bottom of the enclosure. Do not run wire through the drain holes. If 
the knockout hole is not being used to run wire through, drill a hole through the bottom of 

the back plate, route the wire through the hole and seal it using a fitting with a few feet of 

conduit or some other sealant between the case and the cable.

Содержание 522352

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды