manualshive.com logo in svg

Pentair 522352, Руководство по установке

Поделиться
Скачать
Pentair 522352 Скачать руководство пользователя страница 18

10

 

EASYTOUCH

® 

PL4/PSL4 Control System Installation Guide 

Control panel 
(fold down to  
access circuit board 
and low voltage 
compartment)

Control Panel 

Retaining 

screw

Control Panel 
Retaining 
screw

EasyTouch PL4/PSL4 Control System Power Center (front view)

(Front door and high voltage compartment panel removed)

Accessing the EasyTouch

®

 PL4/PSL4 Control System 

Circuit Board and Electronics

The main EasyTouch PL4/PSL4 Control System circuit board is located behind the control panel 
located on the front of the Power Center.  The main circuit board provides connectors for the 
auxiliary relays, valve actuators and sensors. To access the circuit board connectors, fold down the 
main control panel. Note: 

To access the EasyTouch PL4/PSL4 Control System circuit board connectors:

1.  Loosen the two retaining screws securing from the top edge of the control panel. 
2.  Fold down the control panel to access the rear of the circuit board for the electrical 

connections.

3.  For relay, valve actuators and sensors installation and connection instructions see the 

following:

• 

Connecting EasyTouch PL4/PSL4 Control System Relays

, page 11

• 

Installing Valve Actuators

, page 12

• 

Installing and Connecting Temperature Sensors, page 13

4.  After electrical connections have be completed, close the control panel and tighten the two 

retaining screws.

Содержание 522352

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды