manualshive.com logo in svg

Pentair 522352, Руководство по установке

Поделиться
Скачать
Pentair 522352 Скачать руководство пользователя страница 27

 

EASYTOUCH

® 

PL4/PSL4 Control System Installation Guide 

 

                                                                                                                    

EASYTOUCH

® 

PL4/PSL4 Control System Installation 

                                                                                                                                                                                            19

 

IMPORTANT! IntelliChlor (SCG) AC transformer wiring Instructions:  When using the EasyTouch PL4/
PSL4 Control System with the IntelliChlor (SCG) option , be sure the IntelliChlor (SCG) AC transformer 
conductors are connected to the PUMP SIDE OF THE MAIN FILTER PUMP RELAY located in the Power 
Center enclosure (see page 31). This ensures that the IntelliChlor cell produces chlorine only when 
the main filter pump is on. This method does not require a ground fault circuit-interrupter (GFCI) for 
the IntelliChlor SCG Power Center.

TO AVOID AN ELECTRICAL HAZARD AND EQUIPMENT DAMAGE TO THE ENCLOSURE 
AND INTELLICHLOR CELL: FIRST DISCONNECT AC POWER TO THE ENCLOSURE 
BEFORE CONNECTING THE INTELLICHLOR COMMUNICATION CABLE.

To connect the IntelliChlor (SCG) transformer conductor to the main filter pump relay:

1. 

Switch AC power OFF

 to the enclosure at the main house panel circuit breaker.

2.  Loosen the two retaining screws securing HIGH VOLTAGE FRONT COVER PANEL. 

Remove the panel from the enclosure (see illustration below).

3. 

Locate the MAIN FILTER PUMP RELAY. Connect the IntelliChlor SCG transformer 

conductors to the LOAD SIDE of the relay as shown on page 31.

4.  After electrical connections have be completed, install the HIGH VOLTAGE FRONT COVER 

PANEL and tighten the two retaining screws to secure in place.

5. 

Switch AC power ON

 to the enclosure.

BEFORE REMOVING THE HIGH VOLTAGE COVER PANEL FROM THE Power 
Center,

 switch the main power 

OFF 

into the home at the main circuit breaker box 

and also switch 

OFF

 the main power to the Power Center. 

Retaining 
screws

HIGH VOLTAGE FRONT 
COVER PANEL

Wiring IntelliChlor

®

 (SCG) Power Center AC Power Cable to 

the Filter Pump Relay

Filter Pump 

Relay

EasyTouch PL4/PSL4 Control System Power Center 

(Front panel removed)

Содержание 522352

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды