manualshive.com logo in svg

Pentair 522352, Руководство по установке

Поделиться
Скачать
Pentair 522352 Скачать руководство пользователя страница 3

                                                                                                                                                                                            

i

 

                                                                               

EASYTOUCH

® 

PL4/PSL4 Control System Power Center Installation Guide 

Contents

IMPORTANT WARNING AND SAFETY INSTRUCTIONS ....................................................................... iii-vi

General Installation Information ....................................................................................................................v

Introduction ................................................................................................................................................ 1

EasyTouch PL4/PSL4 Control System Power Center Installation Overview ................................................ 3

      Preparing the Power Center Enclosure .................................................................................................. 5

Mounting the Power Center .......................................................................................................................... 6

Installing Conduit and Conductors to the Power Center .............................................................................. 7

Connecting AC Power to the Power Center ................................................................................................. 7

Electrical Wiring High Voltage Connections ................................................................................................. 8

Accessing the Circuit Board and Electronics ............................................................................................. 10

Connecting the Relays ............................................................................................................................... 11

Installing Valve Actuators ........................................................................................................................... 12

    Adjusting the valve position .................................................................................................................... 12

Installing and Connecting Temperature Sensors ........................................................................................ 13

    Water Temperature Sensor .................................................................................................................... 13

    Ambient Air Temperature Sensor (for freeze protection) ........................................................................ 13

    Solar Temperature Sensor (Optional) ..................................................................................................... 15

Connecting a Standard Gas Heater ........................................................................................................... 16

Wiring Pentair UltraTemp Heat Pump ........................................................................................................ 17

Wiring Pentair IntelliFlo Pumps .................................................................................................................. 17

Connecting IntelliChlor (SCG) RS-485 Communication Cable to the Power Center ................................. 18

Wiring IntelliChem Controller to the Power Center..................................................................................... 18

Wiring IntelliChlor (SCG) Power Center AC Power Cable to the Filter Pump Relay .................................. 19

Rewiring the EasyTouch Control System Transformer for 240 VAC ........................................................... 20

Accessories: ............................................................................................................................................. 34

EasyTouch PL4/PSL4 Control System Indoor Control Panel Installation ................................................... 21

EasyTouch PL4/PSL4 Control System QuickTouch II Wireless Controller Installation  .............................. 25

EasyTouch PL4/PSL4 Control System Outdoor Control Panel Installation  ............................................... 28

EasyTouch PL4/PSL4 Control System Circuit Board Connections  ........................................................... 30

EasyTouch PL4/PSL4 Control System Wiring Diagram   ........................................................................... 31

System Start-Up......................................................................................................................................... 32

    Check Electronics .................................................................................................................................. 32

    System Test ............................................................................................................................................ 32

    Testing the auxiliary relays ..................................................................................................................... 32

Solar System Installation ........................................................................................................................... 33

    Solar System Start-Up ........................................................................................................................... 33

Replacement Parts List  ............................................................................................................................. 34

Plumbing Requirements ............................................................................................................................. 35

Equipment Location ................................................................................................................................... 36

Glossary .................................................................................................................................................... 38

Содержание 522352

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды