Pentair 460763 Скачать руководство пользователя страница 51

Страница: 51 / 56

P/N S794 Rev. H 8-11-14

MAX-E-THERM

Pool and Spa Heater Installation and User’s Guide

MAX-E-THERM

HEATERS REPLACEMENT PARTS

REPAIR PARTS – BURNER SYSTEM

Model

Key Part

SR200NA

SR200LP

SR200HD

SR333NA

SR333LP

SR333HD

SR400NA

SR400LP

SR400HD

460763 - NA

460764 - LP

No. Description

Qty.

Combination Gas Control Valve Kit

42001-0051S

3/4" Union

38404-4097S

Gas Orifice

Gas Orifice O-Ring

•

Gas Orifice Kit – NG (Incl. Key Nos. 3 and 4)†

77707-0431

77707-0421

77707-0411

•

Gas Orifice Kit – Propane (Incl. Key Nos. 3 and 4)†

77707-0461

77707-0451

77707-0441

•

NG to Propane Conversion Kit

(Incl. Key Nos. 3 and 4)†

77707-1461

77707-1451

77707-1441

•

Propane to NG Conversion Kit

(Incl. Key Nos. 3 and 4)†

77707-1431

77707-1421

77707-1411

Air Blower Kit

Natural Gas Units

77707-0251

77707-0252

77707-0253

Propane Units

77707-0254

77707-0255

77707-0256

•

Air Orifice Kit (Includes Key Nos. 6 and 7)

77707-0111

77707-0112

77707-0113

Air Orifice

Air Orifice Grill

42001-0114S

•

Blower/Adapter Plate Gasket Kit

(Includes Key Nos. 8, 9, 10, 12)

77707-0011

•

Flameholder Kit (Includes Key Nos. 10, 11, 12, 13

and on 333 & 400 models only -

Flameholder Insert)

77707-0202

77707-0203

77707-0204

Blower/Adapter Plate Gasket

Blower Adapter Plate

Flameholder/Adapter Plate Gasket

Flameholder Assembly

Flameholder/Combustion Chamber Gasket *

Flameholder Insulation Cap

•

Flameholder Insert

Condensate Evaporator Plate

One Piece Metal Chamber/Combustion Chamber
Assembly

42001-0001S

Lower Enclosure

•

Insulation Kit (Includes Key Nos. 13, 15, 23, 24, 25
and 26)

Hex Washer Head S.S. Sheet Metal Screw

Lower Enclosure Insulation

Top Outer Insulation Blanket *

Upper Enclosure Fastener: #12-11x2-1/2" Type AB,

Enclosure Kit, Upper Left-Hand – Natural Gas

Enclosure Kit, Upper Left-Hand – LP Gas

•

77707-3200L

77707-3333L

77707-3400L

77707-3200N

77707-3333N

77707-3400N

77707-0008

77707-0002

Bottom Outer Insulation Blanket *

1" Bottom Inner Insulation

1" Top Insulation

42001-0074S

One Piece Metal Elbow/Combustion Chamber

Cover Assembly

Metal Vent Cover

42002-0005S

Enclosure Kit, Upper Right-Hand

Not available separately.

†

Not included with heater. Order separately .

For heaters manufactured between 1/12/2009 and 10/31/2013 (clamp lid tub design)

Note: Kits also include Clamp Assembly, O-Ring and Silicon Tube.

For heater manufactured AFTER 10/31/2013 (New 9-bolt lid tub design)

For heater manufactured BEFORE 1/12/2009

474095

474957

42001-0200S

474094

474958

42001-0214S

•

Combustion Chamber O-Ring Kit

474952

474201

•

Combustion Air Intake Duct Connection Kit

475002

Содержание 460763

























































Результаты поиска

Содержание 460763

Отзывы:

Похожие инструкции для 460763

Бренды по названию

Популярные бренды

Pentair 460763, Инструкция по установке и эксплуатации

Результаты поиска

Содержание 460763

Отзывы:

Похожие инструкции для 460763

Бренды по названию

Популярные бренды