background image

7

  

E-03-577 (01-23-20)

Pump Troubleshooting

Below is a list of common problems and the probable causes:
Pump will not start.
1.  No power to the motor. Check for blown fuse or open circuit 

breaker.

2.  Selector switch may be in the Off position.

3.  Control circuit transformer fuse may be blown.

4.  Overload heater on starter may be tripped. Push to reset.

Pump will not start and overload heaters trip.

1.  Turn off power and check motor leads with Megger or 

ohmmeter for possible ground.

2.  Check resistance of motor windings. All 3 phases should 

show the same reading.

3.  If no grounds exist and the motor windings check OK, 

remove pump from sump and check for clogged or blocked 
impeller.

Pump operates with selector switch in Hand position but will 
not operate in Auto position.

1.  This indicates trouble in the float level control or the 

alternator relay.

2.  Check control panel for trouble.

Pump runs but will not shut off.

1.  Pump may be air locked. Turn pump off and let set for 

several minutes, then restart.

2.  Lower float control may be hung-up in the closed position. 

Check in sump to be sure control is free.

3.  Selector switch may be in the Hand position.

Pump does not deliver proper capacity.

1.  Discharge gate valve may be partially closed or partially 

clogged.

2.  Check valve may be partially clogged. Raise level up and 

down to clear.

3.  Pump may be running in wrong direction. Low speed pumps 

can operate in reverse direction without much noise or 
vibration.

4.  Discharge head may be too high. Check total head with 

gauge when pump is operating. Total head is discharge 
gauge pressure converted to feet plus vertical height from 
water level in sump to center line of pressure gauge in 
discharge line. Gauge should be installed on pump side of 
all valves. Multiply gauge pressure in pounds by 2.31 to get 
head in feet.

5.  If pump has been in service for some time and capacity falls 

off, remove pump and check for wear or clogged impeller.

Motor stops and then restarts after short period but overload 
heaters in starter do not trip.

1.  This indicates heat sensors in the motor are tripping due 

to excessive heat. Impeller may be partially clogged giving 
a sustained overload but not high enough to trip overload 
heater switch.

2.  Motor may be operating out of liquid due to a failed level 

control.

3.  Pump may be operating on a short cycle due to sump being 

too small or from water returning to sump due to a leaking 
check valve.

TROUBLESHOOTING

A

C

D

B

CHOPPER PLATE

3/8-16 BOLTS

PLATE RETAINING RING

1/2-20 BOLTS

CUTTER INSERT

IMPELLER

RECOMMENDED

MAX CUTTER GAP

.015

.010

Содержание C4S(X)P Series

















Отзывы: